Hearth and Home Technologies CASTILE-CSB, CASTILE-MBK1, CASTILE-PMH1 owner manual Component Function

R

Castile Pellet Stove

	Reference Materials
		￿
Component Function				When describing the location of a component,
				it is always AS YOU FACE THE FRONT OF
A.11
1. Control Box				THE APPLIANCE.
a. The control box is located on upper right side of
			7. Heat Exchangers
appliance, behind the right side panel and above the
vacuum switch.			The heat exchangers transfer hot air from the exhaust system
b. There is a light located inside of the control box. The			into convecton air. Remove the stainless steel top baffle to
internal light will turn green when the appliance has			access the heat exchangers. There are 2 clean out rods
reached a temperature of 175οF (79°C) in the firepot.			located under the heat exchangers.
and will turn red when it reaches 600oF (315°C).			8. Heat Output Switch

c. There is also an internal blue light located in the upper

The heat output switch is located on the upper right rear

left corner of the control box. When you plug in the

corner. The funtion of the heat ouput switch is to regulate

appliance the blue light will automatically start blinking

4 times in a row for 60 seconds and then will stop.

the burn rates; low, medium and high settings.

NOTE:

Do NOT open the control box. This will void the warranty. FolIow proper shutdown procedures first if you need to plug in or remove the control box.

2.Convection Blower

The convection blower is mounted at the bottom rear of the appliance. There are 2 impellers, one on each side of the motor. The convection blower pushes heated air through the heat exchange system into the room.

3.Combustion Blower

The combustion blower is located on the right side of appliance and is designed to pull the exhaust from the appliance and push it out through the venting system.

4.Feed System

The feed system is located on the right side of the appliance and can be removed as an entire assembly. The assembly includes the feed motor, mounting bracket, bearing and feed spring (auger). The hollow feed spring (auger) pulls pellets up the feed tube from the hopper area and drops them down the feed chute into the firepot.

5.Firepot

9.Igniter

The igniter is mounted on the base of the firepot. Combustion air travels over the red hot igniter creating super heated air that ignites the pellets.

10.Junction Box And Wiring Harness

The junction box is located on the right side of the appliance, behind the right side panel. The junction box and wiring harness are replaced as one component.

11.Power Supply

The power outlet is located on the lower right rear corner. Check the wall receptacle for 120 volt, 60 Hz (standard current). Make sure the outlet is grounded and has the correct polarity. A good surge protector is recommended.

12.Red Call Light

The red call light is on the front of the junction box, behind the control box. The function of the red call light is to indicate that the thermostat is calling for heat.

13.Reset Button

The reset button is located on the back of the appliance on the upper right corner of the side panel under the heat output control switch. The function of the button is to momentarily open the thermostat circuit, which restarts the system.

14.Thermocouple

The firepot is made of high quality ductile iron and has a cleaning pull-out rod. The floor of the firepot opens for cleaning when you pull out the rod. Be sure that the floor returns to a completely closed position or your appliance will not operate properly.

6.Fuse

The thermocouple is located on top of the firepot inside the thermocouple cover (ceramic protection tube). The thermocouple sends a millivolt signal to the control box indicating the preset temperatures of the green and red lights have been obtained.

15.Thermostat

The fuse is located on the front of the junction box on the right side of appliance. The fuse will blow should a short occur and shut off power to the appliance.

The appliance is designed to run on a 12 volt AC thermostat. The heat anticipator should be set on the lowest setting available.

September 1, 2008 250-6422E Page 35