Hearth & Home Technologies Inc. 800 W.

Jefferson, Lake City, MN 55041.

F. WIRING

Note: This appliance must be electrically wired and grounded in accordance with local codes or, in the absence of local codes, with National Electric Code ANSI/NFPA 70-latest edition or the Canadian Electric Code, CSA C2.1 as appropriate.

All wiring to be done by a qualified electrician. Use appropriate wire to meet local and national codes for rated power consumption.

1. Power Supply Wiring

Note: Optional Accessories Requirements: Wiring for optional accessories should be done now to avoid reconstruction.

CAUTION:

Label all wires prior to disconnection when servicing controls. Wiring errors can cause improper and dangerous operation. Verify proper operation after servicing.

a.110/120VAC Wall Outlet Installation

1)The appliance is wired from factory with a polarized plug.

2)For ease of electrical hook up, you may wish to install the appliance near an existing outlet. A 15 amp, 120 volt circuit is required. A dedicated circuit is preferred but not essential in all cases. A dedicated circuit will be required if, after installation, the circuit trips or fuse blows on a regular basis when the appliance is operated. Additional appliances on the same circuit may exceed the current rating of the circuit breaker.

3)Before plugging appliance into wall outlet, make sure all control switches are in the “OFF” position. To access the controls, lift up on the lower grille panel and rotate it forward.

4)If the power cord is not being used, go to Step 1b below. If the cord does not reach the outlet, a No. 16-AWG minimum wire size extension cord rated for a minimum of 1875 watts may be used.

b.110/120VAC Hardwire Installation (Minimum 14 gauge two conductor wire, non-metallic sheathing with ground.)

1)Turn off circuit breaker.

2)Remove cover plate located on the right side of appliance.

3)Disconnect black (L1) and white (L2) wires between the appliance and plug. Remove the power cord from the cover plate. Remove the electrical knockout and install the cable clamp (not provided) onto the cover plate. Remove the connectors on the wires from the appliance and strip them back ½”.

4)Feed 8” of service wire through cable clamp and secure.

5)Connect black (L1) and white (L2) wires of the appliance to the black and white wires from the service. Connect green (ground) wire from appliance to the ground of the service. See Figure 3.

6)Wall switch wiring (see below) is to be done at this time.

7)Replace the cover plate onto the appliance.

8)Remove the protective cover by cutting the tape located on the outer perimeter and follow Section “H. Final Installation” on setting up the appliance.

c.HT240V Heater Kit and 208/220/240VAC Hardwire Installation (Minimum 14 gauge three conductor wire, non-metallic sheathing with ground.)

1)Turn off circuit breaker.

2)Remove cover plate located on the right side of appliance.

3)For HT240V installation only, disconnect black (L1) and white (L2) wires between the appliance and plug. Remove the power cord (HT240V only) from the cover plate.

4)Remove the electrical knockout and install the cable clamp onto the cover plate. Remove the connectors on the wires from the appliance and strip them back ½”.

5)Feed 8” of service wire through cable clamp (not provided) and secure.

6)Connect black (L1), white (L2) and red (L3) wires of the appliance to the black, white and red wires from the service. Connect green (ground) wire from appliance to the ground of the service. See Figure 4.

7)Wall switch wiring (see below) is to be done at this time.

8)Replace the cover plate onto the appliance.

9)Remove the protective cover by cutting the tape located on the outer perimeter and follow Section “I. Final Installation” on setting up the appliance.

2. Wall Switch Wiring (24VAC)

*Do not connect wires to 120/208/240VAC*

(hardwired appliances only)

a.Turn off circuit breaker.

b.Remove cover plate located on the right side of appliance.

c.Feed 8” of wire for the wall switch through the cable clamp and secure. Low voltage wire can be used for the wall switch connection. It is recommended to only go 10’ from the appliance to the wall switch.

7

CRESTFIRE SERIES ELECTRIC FIREPLACE

10/03 4030-239 Rev G

Page 7
Image 7
Hearth and Home Technologies CF550EV, CF750EV (208/240V) warranty Power Supply Wiring, Hardwired appliances only

CF550EV, CF750E (120V), CF550E, CF750EV (208/240V) specifications

Hearth and Home Technologies has established itself as a leader in providing innovative heating solutions that combine efficiency, style, and functionality. The CF750EV (208/240V), CF550E, CF750E (120V), and CF550EV are among their latest electric fireplace offerings, designed to cater to various needs and preferences.

The CF750EV is a robust model that operates on 208/240V, featuring an impressive heat output while maintaining energy efficiency. This model is equipped with advanced technology, allowing users to customize their heating experience. It boasts a realistic flame presentation, adjustable flame intensity, and a user-friendly LED display, making it an aesthetically pleasing addition to any space. The CF750EV also includes a built-in thermostat and a remote control, offering convenience and control at your fingertips.

The CF550E is designed for those seeking a compact solution without compromising on performance. This electric fireplace operates effectively at 120V, making it suitable for spaces where electrical capacity may be limited. Its sleek design allows for easy installation in various room configurations, and it provides an inviting ambiance while efficiently warming the area.

In contrast, the CF750E is another 120V model that stands out for its higher heat output compared to the CF550E. This fireplace also features adjustable flame effects, enhancing its visual appeal. The unit’s clean lines and modern design make it a versatile choice for contemporary homes. The CF750E is also integrated with safety features such as overheating protection, ensuring peace of mind during use.

Lastly, the CF550EV model combines the best of both worlds with its advanced electric technology and fireplace aesthetics. This unit is designed to complement any décor while providing warmth and a cozy atmosphere. The CF550EV includes customizable heat settings and a realistic flame effect, making it suitable for year-round use, regardless of the season.

Collectively, these models from Hearth and Home Technologies embody the perfect blend of technology, design, and functionality. They cater to various needs, whether you are looking for a powerful heating solution or a stylish accent piece for your living space. With their emphasis on efficiency and modern features, these electric fireplaces stand as a testament to the brand’s commitment to quality and innovation in home heating solutions.