Manuals / Brands / Household Appliance / Indoor Fireplace / Hearth and Home Technologies / Household Appliance / Indoor Fireplace

Hearth and Home Technologies EM-415 - 36, EM-485T - 42 F. Tools and Supplies Needed H. Inspect Fireplace and Components, G. Typical Fireplace System

1 52

Download 52 pages, 4.4 Mb

17

Before beginning the installation be sure the following

tools and building supplies are available:

Reciprocating saw Framing material

Pliers High temp caulking material

Hammer Gloves

Phillips screwdriver Framing square

Flat blade screwdriver Electric drill and bits

Plumb line Safety glasses

Level Tape measure

1/2-3/4 in. length, #6 or #8 self-drilling screws

Misc. screws and nails

F. Tools and Supplies Needed H. Inspect Fireplace and Components

WARNING! Risk of Fire and/or Explosion! Damaged

parts could impair safe operation. DO NOT install dam-

aged, incomplete or substitute components. Keep ﬁ re-

place dry.

• Remove ﬁ replace and components from packaging and

inspect for damage.

• Vent system components and doors are shipped in

separate packages.

• Report to your dealer any parts damaged in shipment.

• Read all the instructions before starting the

installation. Follow these instructions carefully

during the installation to ensure maximum safety

and beneﬁ t.

G. Typical Fireplace System

This ﬁ replace system requires:

• Fireplace/integral grate/refractory/outside air system

• Chimney system and termination cap

• Hearth extension

Heat & Glo • EM-415, EM-485 • 33056 • Rev W • 10/08

Contents

Main Owners Manual Models: EM-415 - 36 EM-485T - 42 Circulating WARNING NOTICE DO NOT DISCARD Homeowner Reference Information FIREPLACE NO. Listing Label Information/Location Congratulations! MODEL NO. MODEL NO. MFG. DATE ! Table of Contents User Guide Installer Guide Hearth & Home Technologies LIMITED WARRANTY Page 1 B. Non-Combustible Materials C. Combustible Materials A. Appliance Certi cation 2 A. Your Fireplace User Guide WARNING C. Starting a Fire B. Seasoned Wood D. Grate E. Firescreen F. Flue Damper I. Outside Air (optional) J. Fan Kit (optional) H. Glass Doors K. Vented Gas Log Sets & Gas Log Lighters L. Optional Components N. Wood Fuel Hardwood vs Softwood Moisture Storing Wood Seasoned Wood 3 A. Disposal of Ashes B. Chimney Inspection/Cleaning Creosote - Formation and Need for Removal C. Check Firebox Refractory D. Inspect Grate E. Glass Cleaning 4 Start Fire Problems Possible Cause Solution 5 A. Typical Fireplace System Installer Guide D. Negative PressureB. Design and Installation Considerations C. Draft E. Locating Fireplace & Chimney F. Tools and Supplies Needed H. Inspect Fireplace and Components G. Typical Fireplace System 6 A. Select Fireplace Location B. Clearances Note: Chimney air kit not shown, but required in Canada. B A D D. Frame the Fireplace C A 2 in. (51 mm) min. air space clearance from chimney. Note: Framing must be extended straight up, all the way to the ceiling. Header MUST NOT be notched! C. Sidewalls/Surrounds 7 A. Things to Consider B. Position the Fireplace C. Place Protective Metal Hearth Strips D. Level Fireplace 3 ft min. from top of uppermost chimney section to air inlet. Note: Chimney air kit not shown, but required in Canada. E. Install Outside Air Kit F. Junction Box Installation G. Installation of Fan 8 A. Chimney Requirements Table 8.1 Table 8.2 B. Using Offsets/Returns C. Assembling Chimney Sections D. Install Chimney Air Kit E. Installing Ceiling Firestops F. Installing Attic Insulation Shield H. Complete Installation The following steps should be skipped if using a chase. I. Install Flashing G. Cut out Hole in Roof J. Chimney Termination Requirements 9 A. Construct the Chase B. Install Fireplace & Chimney C. Install Chase Top D. Install Termination Cap TR342 Round Telescoping Termination Cap Install the chimney sections up through the chase enclo- sure. ST375 Square Termination Cap Figure 9.4 Installing a TR344 Round Termination Cap European Copper Series Termination Cap Figure 9.7 Installing a TS345/TS345P Square Termination Cap TCT375 Terra Cotta Cap TS345/TS345P Square Termination Cap Figure 9.8 Installing a TCT375 Terra Cotta Cap European Copper Series Termination Cap Figure 9.9 Installing an Adapter for European Copper Cap Se- ries (CT-King shown) 10 Open Top Shroud (TR342 & TR11/TR11T caps require radiation shield) A. Radiation Shield B. Field Constructed Shrouds 3 in. (76 mm) Min. Opening Height Min. Base Dim Roofed Style Shroud (radiation shield required) Min. Height above radiation shield Min. Base Dim 3 in. (76 mm) Min. Radiation Shield Height from top of Chase Min. Opening Width Mailbox Style Shroud (radiation shield required) 11 11 R = 1/k x inches of thickness Table 11.2 A. Non-Combustible Materials D. Finishing Material E. Combustible Mantel B F. Sidewalls/Surrounds A 12 in. [305 mm] 9 3/4 in. [248 mm] 12 in. [305 mm] 12 12 A. Gas Log/Lighter Provision B. Wood Burning Inserts C. Install Fan 13 13 A. Fireplace Dimensions Catalog # Description B. Fireplace Components B. Fireplace Components (continued) C. Chimney Components ID4 Insulated Duct i UD4 Uninsulated Duct 42 in. (1067 mm) A B14-1/2 in. (368 mm) Page Heat & Glo EM-415, EM-485 33056 Rev W 10/08 D. Service Parts Traditional Brick Part number list on following page. EM-415 Stocked at Depot D. Service Parts (continued) Page NOTES E. Contact Information DO NOT DISCARD THIS MANUAL CAUTION DO NOT DISCARD