F. Installing Attic Insulation Shield

WARNING! Risk of Fire! You MUST install an attic insu- lation shield when there is any possibility of insulation or other combustible material coming into contact with the chimney.

DO NOT pack insulation between the chimney and the attic insulation shield.

Failure to keep insulation and other materials away from chimney pipe could cause fire.

DO NOT offset chimney inside insulation shield.

Installation of a ceiling firestop is required

Refer to Figures 8.6 - 8.8.

Roll the shield (around the chimney if already installed) until you have a 3 in. (76 mm) overlap and the three holes on each side match up (large holes on top).

Insert three screws into the matching holes to form a tube.

Bend three tabs on the bottom of the tube inward to 90° to maintain chimney air space as shown in Figure 8.6.

Rest the insulation shield on the ceiling firestop below.

Bend the three short tabs at the top of the shield inward to 90° to maintain the 2 in. (51 mm) air space from the chimney.

Bend the remaining top tabs to just meet the pipe.

If you wish to make a custom shield or barrier, follow these guidelines:

Metal is preferred, although any material stiff enough to hold back the insulation can be used.

WARNING! Risk of Fire! Use of cardboard or other materials that can deflect under humidity or other envi- ronmental conditions is not recommended.

The shield or barrier must be tall enough to extend above the insulation and prevent blown-in insulation from spilling into the cavity.

Maintain specified air spaces around chimney.

Check instructions and local codes for further details.

 

 

 

 

Bend remaining tabs

 

 

 

 

to rest against pipe to

Bend

 

inward

prevent insulation

90°

 

from falling in.

 

 

 

 

 

Insert three

 

 

 

 

screws

3 in. (76 mm) overlap

Figure 8.6 Prepare Attic Insulation Shield

 

 

Tabs bent in to

 

Pipe

rest against pipe

 

 

 

 

Attic Insulation Shield

 

 

14-1/2 in. (368 mm)

 

6 Tabs bent

diameter

 

in 90°

Ceiling Firestop

 

 

Insulation

Pipe

Insulation

10-1/2 in.

(267 mm)

Figure 8.7 Install Attic Insulation Shield (firestop above ceiling)

 

 

Tabs bent in to

 

 

rest against pipe

 

Pipe

 

 

 

Attic Insulation Shield

 

 

14-1/2 in. (368 mm)

 

 

diameter

 

6 Tabs bent

 

 

in 90°

 

Insulation

 

Insulation

10-1/2 in.

Pipe

Ceiling Firestop

(267 mm)

 

 

Figure 8.8 Install Attic Insulation Shield (firestop below ceiling)

Heat & Glo • EM-415, EM-485 • 33056 • Rev W • 10/08

29

Page 29
Image 29
Hearth and Home Technologies EM-485T - 42, EM-415 - 36 Installing Attic Insulation Shield, Prepare Attic Insulation Shield

EM-485T - 42, EM-415 - 36 specifications

Hearth and Home Technologies has long been a leader in the fireplace and heating solutions industry, and among their latest offerings is the EM-415 - 36 and EM-485T - 42 models. These elegant units blend aesthetics with advanced technology, making them a perfect addition to any modern home.

The EM-415 - 36 model features a 36-inch viewing area, offering an expansive flame look that enhances any room's ambiance. On the other hand, the EM-485T - 42 boasts a larger 42-inch viewing area, providing an even more impressive visual display. Both designs prioritize an open front that allows for maximum natural light while showcasing the fire's beauty.

One of the main features of both models is their efficiency. They utilize advanced venting systems that allow for a balanced flow of air and smoke, ensuring that the fire burns cleanly and efficiently. This not only contributes to a reduced environmental impact but also helps to lower energy costs for homeowners. The EM-415 and EM-485T are designed to meet or exceed various efficiency standards, making them a responsible choice for homeowners concerned about energy use.

In terms of heat output, both models are equipped with powerful burners that provide ample warmth for larger spaces. With adjustable flame settings, users can customize their experience to either enjoy a cozy fire during colder months or opt for a gentle warmth that’s suitable for entertaining during milder weather.

The aesthetic design of the EM-415 and EM-485T is another notable feature. They come with various customizable options, including different finishes and decorative media, allowing homeowners to tailor the appearance to their personal style and home decor. The clean, contemporary aesthetic ensures that these fireplaces are not just functional, but also a centerpiece of elegance in any room.

Installation is made convenient thanks to the thoughtfully designed systems in both models. They can be installed easily in a variety of settings, including new constructions and renovations. The straightforward operation and maintenance further ensure that homeowners will enjoy these fireplaces hassle-free.

Safety is also paramount with Hearth and Home Technologies. The EM-415 and EM-485T units are fitted with advanced safety mechanisms, such as automatic shut-off features and protective screens, ensuring peace of mind for users and their families.

In conclusion, the Hearth and Home Technologies EM-415 - 36 and EM-485T - 42 models combine striking aesthetics with advanced technology and efficiency. Their innovative features and safety measures make them appealing options for those looking to elevate their living space while enjoying the warmth and ambiance of a beautiful fire.