Install Fireplace & Chimney | Hearth and Home Technologies SC60

B. Install Fireplace & Chimney

Install as per Sections 7 and 8.

C. Install Chase Top

•You MUST use a chase top in a chase installation. Chase tops are available from your Heatilator dealer or may be ﬁeld constructed.

•Include a turndown and drip edge to prevent water from seeping into the chase.

•Include a 2 in. (51 mm) soldered, welded or spun collar around pipe opening to keep water out.

•Provide a 1/8 in. (3 mm) gap around the ﬂue pipe.

•Slope the chase top downward away from the opening.

WARNING! Risk of Fire! DO NOT caulk the pipe to the chase top collar.

•Caulk all seams to prevent leaks.

•Refer to Figure 9.3.

Slope Downward (1/4 in. per foot minimum)

2 in. (51 mm) Collar on Chase Top

Turn-down

Drip Edge

Chase

.018 (26 ga) min. Galvanized Chase Top

Figure 9.3 Chase Top Construction

32	Heatilator • SC60 • 32838 Rev X • 10/08

Page 32

Image 32

Hearth and Home Technologies SC60 owner manual Install Fireplace & Chimney, Install Chase Top

Contents

Fire Risk Wood Burning FireplaceHot screen/mesh and glass doors will cause burns Number Listing Label Information/LocationGrate Table of Contents Installer GuideSafety Alert Key User Guide Hearth & Home Technologies Limited Warranty CONDITIONS, Exclusions & Limitation of Liability Heatilator SC60 32838 Rev X 10/08 Listing and Code Approvals Appliance CertiﬁcationNon-Combustible Materials Combustible Materials Hot glass will cause burns Operating InstructionsYour Fireplace Seasoned Wood Starting a FireGrate Firescreen Glass Doors Vented Gas Log Sets & Gas Log LightersOptional Components Clear Space Wood Fuel Maintainance and Service Chimney Inspection/CleaningDisposal of Ashes Creosote Formation and Need for Removal Glass Cleaning Check FirebrickInspect Grate Frequency As desired Troubleshooting Guide Start Fire Problems Possible Cause Solution Getting Started Typical Fireplace System Negative Pressure Design and Installation ConsiderationsDraft Locating Fireplace & Chimney Frequently open doors Central heat outlets or returns Inspect Fireplace and Components Tools and Supplies NeededFireplace System Requirements Framing & Clearances Select Fireplace Location Clearances Clearances to Combustible Materials Sidewalls/Surrounds Frame the Fireplace Installation of Fireplace Things to ConsiderPosition the Fireplace Place Protective Metal Hearth Strips Ft min. from top of uppermost chimney section to air inlet Install Outside Air Kit To service or replace the fan kit Chimney Assembly Chimney Requirements Height of Chimney Components Using Offsets/Returns Example Assemble Chimney Sections Install Chimney Air KitInstall Ceiling Firestops Install Attic Insulation Shield Prepare Attic Insulation Shield Complete Installation Install FlashingFollowing steps should be skipped if using a chase Cut out Hole in Roof Chimney Termination Requirements Flat Roofs Chase Installations Construct the Chase Install Fireplace & Chimney Install Chase Top Install Termination Cap ST375 Square Termination Cap TS345/TS345P Square Termination Cap Shrouds Radiation ShieldField Constructed Shrouds Open Top Shroud TR342 caps require radiation shield Mailbox Style Shroud radiation shield required Roofed Style Shroud radiation shield required = 1/k x inches of thickness FinishingHearth Extension Finishing Material HX3 or HX4 Hearth Ext or equivilent insulation Combustible Mantel Firebrick Installation 13 Side Brick Installation Accessories Gas Log/Lighter ProvisionWood Burning Inserts Gas Code, Ansi Z223.1 Materials Fireplace 1321 mm 406 mm Chimney Components Catalog # 14-1/2 10-7/8 276 mm Service Parts Contact Information

B. Install Fireplace & Chimney

C. Install Chase Top

Figure 9.3 Chase Top Construction

Heatilator • SC60 • 32838 Rev X • 10/08