Hearth and Home Technologies SC60 guide

•TS345/TS345P Square Termination Cap

Termination Cap

Collar

2 in. (51 mm)

Minimum Height

Chase Top

Chimney

Pipe

Place waterproof sealer under each flange of the termina- tion cap and on top of each screw to help prevent leaks.

3 in. (76 mm)

Maximum

top of chase to top of

chimney section

Chase

Termination cap pipe and chimney section must overlap 1-1/2 in. (38 mm).

Figure 9.7 Installing a TS345/TS345P Square Termination Cap

•TCT375 Terra Cotta Cap

Collar

2 in. (51 mm)

Minimum Height

Chase Top

Place waterproof sealer under each flange of the termina- tion cap and on top of each screw to help prevent leaks.

Termination Cap

The last section of pipe must stop between 2 in. (51 mm) above top of chase and 7 in. (178 mm) below top of chase

2 in. (51 mm)

7 in. (178 mm)

Chase

Chimney

Pipe

Termination cap pipe and chimney section must overlap 1-1/2 in. (38 mm)

Figure 9.8 Installing a TCT375 Terra Cotta Cap

34	Heatilator • SC60 • 32838 Rev X • 10/08

Image 34

Hearth and Home Technologies SC60 owner manual TS345/TS345P Square Termination Cap

Contents

Hot screen/mesh and glass doors will cause burns Wood Burning FireplaceFire Risk Grate Listing Label Information/LocationNumber Safety Alert Key Table of ContentsInstaller Guide User Guide Hearth & Home Technologies Limited Warranty CONDITIONS, Exclusions & Limitation of Liability Heatilator SC60 32838 Rev X 10/08 Non-Combustible Materials Listing and Code ApprovalsAppliance Certiﬁcation Combustible Materials Your Fireplace Operating InstructionsHot glass will cause burns Grate Seasoned WoodStarting a Fire Firescreen Optional Components Glass DoorsVented Gas Log Sets & Gas Log Lighters Clear Space Wood Fuel Disposal of Ashes Maintainance and ServiceChimney Inspection/Cleaning Creosote Formation and Need for Removal Inspect Grate Glass CleaningCheck Firebrick Frequency As desired Troubleshooting Guide Start Fire Problems Possible Cause Solution Getting Started Typical Fireplace System Draft Design and Installation ConsiderationsNegative Pressure Locating Fireplace & Chimney Frequently open doors Central heat outlets or returns Fireplace System Requirements Tools and Supplies NeededInspect Fireplace and Components Framing & Clearances Select Fireplace Location Clearances Clearances to Combustible Materials Sidewalls/Surrounds Frame the Fireplace Position the Fireplace Installation of FireplaceThings to Consider Place Protective Metal Hearth Strips Ft min. from top of uppermost chimney section to air inlet Install Outside Air Kit To service or replace the fan kit Chimney Assembly Chimney Requirements Height of Chimney Components Using Offsets/Returns Example Install Ceiling Firestops Install Chimney Air KitAssemble Chimney Sections Install Attic Insulation Shield Prepare Attic Insulation Shield Following steps should be skipped if using a chase Complete InstallationInstall Flashing Cut out Hole in Roof Chimney Termination Requirements Flat Roofs Chase Installations Construct the Chase Install Fireplace & Chimney Install Chase Top Install Termination Cap ST375 Square Termination Cap TS345/TS345P Square Termination Cap Field Constructed Shrouds ShroudsRadiation Shield Open Top Shroud TR342 caps require radiation shield Mailbox Style Shroud radiation shield required Roofed Style Shroud radiation shield required Hearth Extension Finishing= 1/k x inches of thickness Finishing Material HX3 or HX4 Hearth Ext or equivilent insulation Combustible Mantel Firebrick Installation 13 Side Brick Installation Wood Burning Inserts AccessoriesGas Log/Lighter Provision Gas Code, Ansi Z223.1 Materials Fireplace 1321 mm 406 mm Chimney Components Catalog # 14-1/2 10-7/8 276 mm Service Parts Contact Information