For units WITHOUT factory installed Rocker Switch
|
|
| BLACK |
|
|
|
|
SWITCH AND WIRE |
|
|
| BATTERIES |
| ||
ASSEMBLY |
|
|
|
|
|
| |
SUPPLIED |
|
|
|
|
|
|
|
WITH |
|
|
|
|
|
| |
|
| WHITE |
|
|
|
|
|
|
| GREEN | BROWN |
| BLACK | RED | YELLOW |
ORANGE |
|
|
| or | |||
|
|
|
|
|
| WHITE | |
GROUND |
|
|
| BLACK | RED |
| |
IPI | BLACK |
|
|
|
| ||
|
|
|
|
| |||
VALVE |
|
|
|
|
| ||
|
|
|
|
|
| ||
|
|
| 1 |
|
|
| G W* R |
|
| IPI | 2 |
| BROWN | ||
|
| 3 |
|
| |||
|
| MODULE | 4 |
| BROWN |
| |
|
| 5 |
|
| |||
|
|
| 6 |
| RED |
| |
|
|
| 7 |
|
| ||
|
|
| 8 | 3V DC |
|
|
|
FLAME | (FEMALE/MALE) |
|
| BLACK |
| ||
|
|
|
| ||||
SOLENOID | RED (MALE/FEMALE) |
|
|
|
|
| |
RED |
|
|
|
|
| ||
|
| FLAME ON | RED |
|
|
|
|
|
|
| RED |
|
|
|
|
|
|
|
|
| ORANGE |
| |
|
| FLAME HIGH/LOW | AC |
|
| ORANGE |
|
ADAPTER WIRES |
|
|
|
|
|
| |
|
| PLUG |
| BLACK |
|
| |
|
|
| AUX |
| BLACK |
| |
|
| CONNECTION |
| GROUND |
| ||
|
|
|
|
|
| ||
* May be labeled as “W” or “Y”. | PIGTAIL | |
GREEN | ||
|
Figure 5. Intellifire (IPI) Wiring Diagram
RED
REAR VIEW
GREEN
G
W*
R
FRONT VIEW
YELLOW FACTORY
YELLOW CONNECTED TOGETHER
FAN THERMOSTAT
FAN
CONNECTION
BLACK
Intellifire (IPI):
Find these parts packed with
•Rocker switch
•Rocker switch bracket
•Strips of Velcro
•Black and white wire pigtails - (2)
•Female ends (not used on IPI applications) - (2)
Slide rocker switch into bracket until it snaps into place. Attach one pigtail to one side of rocker switch and the other pigtail to the other side of the rocker switch. Find the two brown wires from IPI module and attach them to the two black wires from the rocker switch. Find the two brown wires from the control box and attach them to the white wires from the rocker switch. Attach the Velcro to rocker switch bracket and place rocker switch next to control box. (Refer to Figure 5).
Proceed to Step 4.
4.If equipped with a fan, plug the fan cord into the power cord labeled “FAN”. Disconnect the two wires from the fan thermostat switch on the fireplace. Disconnect the two yellow wires from each other and connect them to the fan thermostat switch. Use one of the existing wires on the thermostat to connect to the proper end on the male terminated yellow wire.
Note: The fan rheostat has now been removed from the circuit and is inoperable. Use the wall switch to change fan speeds. The fan temperature sensor is still operable and will turn the fan on and off when the fireplace heats up and cools down.
5.Remove the screw and knob from the variable regulator and discard.
6.Unscrew the nut from the regulator and discard.
7.Remove the bag containing a washer and blue and red plungers from the side of the flame control solenoid.
8.Place washer on flame control solenoid (see Figure 6).
4
