GAS CONTROL

 

KNOB

 

VALVE

 

 

 

 

 

SCREW

 

 

 

NUT

 

WASHER

VARIABLE REGULATOR

 

 

 

 

 

WASHER

 

VARIABLE

 

SOLENOID

 

REGULATOR

 

 

 

FLAME CONTROL

VARIABLE

JAM NUT

Figure 6.

SOLENOID

REGULATOR

PLUNGER

 

 

 

 

9.Insert the correct plunger (blue - natural gas, red - pro- pane) into the flame control solenoid (see Figure 6).

10.Thread the flame control solenoid with correct plunger into the thread hole in the variable regulator. Turn into valve approximately two full turns. Do not tighten or damage may occur.

11.Set the valve manifold pressure to the proper setpoint. The setpoint is adjusted by rotating the solenoid to adjust its depth into the valve. Using a manometer to monitor pressure, rotate the solenoid so that the output is set to proper range.

12.Tighten the jam nut on the threaded shaft of the solenoid against the valve regulator. Use an open- ended ½” wrench to tighten the nut, while holding the solenoid in the proper position. This step will en- sure that the solenoid remains locked into the proper position.

13.Connect orange wires from control box to the flame control solenoid.

14.Ground the control box by attaching the green ground wire (has round ring-terminal on end) to the fireplace base pan or appropriate ground.

CAUTION

Lay the control box and wires flat on the base pan to avoid potential overheating problems.

Intellifire (ipi) models only

For units with factory installed rocker switch see Fig. 3.

For units without factory installed rocker switch see Fig. 5.

14.Disconnect main valve wire (green) from the front of the valve. Connect red control wire to red adapter wire containing one large male end and one small female end and connect to valve terminal (see Figure 3). Connect the other red control wire to red adapter wire containing one large female end and one small male end and connect the green module wire (previously disconnected from valve front).

15.Carefully unplug battery pack wires from IPI module. Plug battery pack into red and black battery wires (labeled “Battery”).

16.Plug red and black wires from control box (labeled “3V DC”) to the red and black wires extending from IPI module (labeled “3V DC”). Red connects to red, black connects to black.

NOTE: Transformer supplied with the IPI system is NOT used. Disconnect the transformer from the electrical junction box. Transformer may be removed from the fireplace, but we recommend leaving it connected to the IPI module.

13.Connect auxiliary functions. This unit is equipped with a 110 VAC supply cord (labeled “AUX”) for controlling auxiliary functions such as an electric ember bed.

5

Page 4 Page 6
Page 5
Image 5
Hearth and Home Technologies WSK-MLT installation instructions Intellifire ipi models only
Page 4 Page 6

WSK-MLT specifications

Hearth and Home Technologies has made significant strides in the home heating industry, and one of their standout products is the WSK-MLT, a multifaceted wood-burning stove that blends efficiency with elegance. Designed for modern homes, the WSK-MLT provides a sustainable heating solution while enhancing the aesthetic appeal of any living space.

One of the key features of the WSK-MLT is its advanced combustion technology. This stove utilizes a secondary combustion chamber that optimizes the burning process, resulting in reduced emissions and improved fuel efficiency. By maximizing the combustion of wood, the WSK-MLT not only ensures a more complete burn but also minimizes the amount of smoke produced. This makes it an environmentally friendly choice for homeowners.

Heat management is another standout characteristic of the WSK-MLT. With its efficient heat exchange system, this stove is capable of producing radiant heat that can warm large areas effectively. The adjustable air control allows users to fine-tune the burn rate, which translates to a longer burn time and a consistent heat output. The stove's large firebox can accommodate longer logs, enhancing its efficiency and reducing the frequency of reloading.

Aesthetics are equally important, and Hearth and Home Technologies have ensured the WSK-MLT does not compromise on style. The sleek design and customizable options, including various finishes and trims, make it a perfect fit for both contemporary and traditional interiors. The large glass door provides a captivating view of the fire, turning it into a focal point of the room.

Safety features have also been prioritized in the design of the WSK-MLT. The stove is equipped with a durable heat shield and cool-touch handles, making it safer for families with children and pets. Additionally, it complies with stringent safety standards, giving homeowners peace of mind.

In summary, the Hearth and Home Technologies WSK-MLT is a premium wood-burning stove that combines advanced technology, excellent heat management, stylish design, and robust safety features. Ideal for those seeking a reliable and efficient heating solution, it represents the perfect fusion of functionality and aesthetic appeal, promising to deliver warmth and comfort in the home for years to come.
Top Page Image Contents