DualBrite®
Replacement Sensor Head
Put the |
| |||||
or 20 minute position. |
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
| TEST 1 5 20 | |||||
|
|
|
|
|
|
|
MANUAL MODE |
|
|
|
|
|
|
Model 5716
Features
• | Turns on lighting when motion is detected. |
• | Automatically turns lighting off. |
• | Three lamp modes available: Normal, Soft, or Flash. |
• | Patented DualBrite® Timer. |
• | Photocell keeps the lighting off during daylight hours. |
• | LED indicates motion was sensed (day or night). |
Manual mode only works at night be- cause daylight returns the sensor to AUTO.
Flip the light switch off for one second then back on to toggle between AUTO and MANUAL MODE.
Manual mode works only with the ON- TIME switch in the 1, 5, or 20 position.
1 Second OFF
then...
... back on.
Requirements
•Not for use with fluorescent lights.
•The light control requires
•If you want to use Manual Mode, the control must be wired through a switch.
•Install sensor in accordance with local codes.OPERATION
Mode: | Works: Day | Night | |
|
|
|
|
Test | 5 Sec | x | x |
|
|
|
|
Normal | 1, 5, 20 min. |
| x |
|
|
|
|
Manual | Until Dawn* |
| x |
|
|
|
|
Accent | 3, 6 Hr. to Dawn |
| x |
| * resets to Auto Mode at dawn. |
|
Note: When first turned on wait about 1 1/2 minutes for the circuitry to calibrate.
TESTPut | DualBrite® | |||||||||||
the sensor bottom to |
|
|
|
|
|
|
|
|
|
|
| |
TEST and the DualBrite® |
|
|
|
|
|
|
|
|
|
|
| |
TEST 1 5 20 | Off 3 6 Dusk to | |||||||||||
switch OFF. | ||||||||||||
|
|
|
|
|
|
|
|
| Dawn | |||
|
|
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
|
| ||
LAMP MODE |
|
|
|
|
|
|
| |||||
|
|
|
| |||||||||
Put the LAMP MODE switch |
|
| LAMP MODE | |||||||||
in the Normal, Soft, or Flash | NORMAL SOFT FLASH | |||||||||||
|
|
|
|
|
|
|
position.
Mode Switching Summary
| TEST |
|
|
|
| Move | ||
| ||||||||
|
|
|
|
|
| |||
|
|
|
|
|
|
|
| 5, or 20 minutes |
|
|
|
|
|
|
| ||
| AUTO |
|
|
|
|
| Flip light switch off | |
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
| for one second then |
|
|
|
|
|
|
|
| back on* |
MANUAL MODE |
|
|
| |||||
|
|
|
|
*If you get confused while switching modes, turn the power off for one minute, then back on. After the calibration time the control will be in the AUTO mode.
DualBrite® TIMER
Light comes on half bright for selected time after dusk (Off, 3 hr., 6 hr., until dawn). Selecting OFF disables this feature.The motion sensing features will continue to work as described in this manual. If motion is sensed, the light turns on full bright for the
LAMP MODES
There are three lamp modes (light
•NORMAL - Light instantly comes on.
•SOFT - Light starts dim and gradually increases to full brightness. Light gradually dims to
•FLASH - Light flashes on then off twice before turning on full brightness.
© 2007 HeathCo LLC |