INSTALLATION
For best performance, mount the fixture about 6 feet (1.8 m) above the ground.
WARNING: Turn power off at circuit breaker.
1. Remove |
|
|
|
|
|
|
|
|
|
| 2. Remove | |||||||
two nuts. |
|
|
|
|
|
| Mounting Plate. | |||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Ground | |
|
|
|
|
|
| ||
|
|
|
|
|
| ||
|
|
|
|
|
| ||
|
|
|
|
|
| Screw | |
3. | Tighten screws | ||||||
Wire Path | |||||||
|
| finger tight. | |||||
|
|
| |||||
|
|
|
|
|
|
| |
4. Attach mounting plate to junction box.
Horizontal Junction Boxes Only:
Fixture | Ground | |
Screw | ||
Screw |
| |
Wire |
| |
Path | Fixture | |
Junction | ||
Screw | ||
Box |
| |
Screws |
|
Remove ground screw and 2 fixture screws from the mounting plate. Flip plate over.
WIRING
BLACK
WHITE
One Motion Light
BLACK BLACK
WHITE 
Two Motion Lights
❒Twist the junction box wires and the fixture wires together as shown below. Secure with wire connectors. If you have a metal junction box, you may not need the green “pigtail”. If you are unsure about the grounding method, consult your local building code.
CAUTION: DO NOT connect the RED wire unless you want to control other lights from the motion sensor.
Recommended Grounding Method
Use a green ground “pigtail” (not provided) and twist one end together with the bare fixture wire and the box ground wire. Secure with a wire connector. Secure the other end of the “pigtail” with the GND screw on the mounting plate.
Black to black 
White to white
