Receiver Information

All receivers have the following features and ratings:

•Rated for 120VAC/60Hz supply voltage.

•Uses existing wiring.

•Fits standard single gang junction box (wall switch only).

•Not for use with Compact Fluorescent bulbs.

•When first turned on wait 15 seconds.

Wall Switch Receiver

Features and Ratings:

• Up to 500 Watt maximum incandescent load depend- ing upon switch purchased. See rating label on switch for exact load rating.

• Not for use with Compact Fluorescent bulbs.

WARNING: FOR USE ONLY with 120 volt incandescent or halogen bulbs.

CAUTION: To reduce the risk of overheating and pos- sible damage to other equipment, do not install to control a receptacle, a motor-operated appliance, a fluorescent lighting fixture, or a transformer-supplied appliance.

ImportantInformationRegarding3-WaySwitchInstallations: In order to use this product where two switches are being used to control the light, the 3-Way Wall Switch transmitter will also have to be installed. Refer to the 3-Way Wall Switch Installa- tion section for details.

Important: When ganging these units, they must be derated as follows:

Gang

1

2

3

 

 

 

 

300 W

300 W

300 W

300 W

500 W

500 W

475 W

450 W

 

 

 

 

Installation

1.Select light switch to be replaced by wall switch receiver.

2. WARNING: Turn off the power to the light switch circuit before you proceed. Do this at your circuit breaker or fuse box.

3.Remove the existing wall plate and switch. Disconnect the two power wires and the ground wire.

Note: If there are more than two power wires attached to the switch, consult an electrician about installation. In addition, some local build- ing codes may require installation by a qualified electrician.

4.If necessary, strip away 1/2" of insulation from end of wires.

5.Connect one of the black power wires from receiver to one of the power wires you removed from the old switch. Use one of the supplied wire connectors to secure the wires (see illustration).

6.Connect the second black power wire from receiver to the other power wire you removed from the old switch. Use one of the supplied wire connectors to secure the wires (see illustration).

7.Connect the green ground wire from receiver to the ground wire removed from old switch. Use one of the supplied wire connectors to secure the wires (see illustration).

8.Check wire connections to make sure they are secure and that no bare wires are exposed.

9.Route antenna between the bottom of the junction box and the wall. Feed antenna into wall cavity while placing wall switch into junction box.

10.Position the wall switch receiver in the junction box with the DIM button located to the right. Use the two wall switch screws (long) supplied to mount the receiver to the wall box (see illustration). Push excess wiring into wall box while you do this. You may need to bend the wires to fit inside the box. Mount wall plate on wall switch receiver with screws (short) provided.

11.Turn on the power to the light switch circuit. Do this at your circuit breaker or fuse box.

 

Ground Wire (Bare or Green)

Junction

 

 

 

Wall

Box

ON/OFF Button Switch

 

Wall Switch Screw

 

Wall Plate

 

 

Screw

 

 

 

 

Wall

 

Antenna

Wall Plate

DIM Button

 

 

 

 

Power Disconnect Switch

 

 

Installing Wall Switch Receiver

 

598-1306-02

Page 5 Page 7
Page 6
Image 6
Heath Zenith 598-1306-02 manual Receiver Information, Installation, Installing Wall Switch Receiver
Page 5 Page 7

598-1306-02 specifications

Heath Zenith 598-1306-02 is a versatile and feature-rich motion-activated outdoor light that enhances home security while providing convenience and energy efficiency. This device is designed to detect motion within a specified range and illuminate outdoor areas, making it an excellent choice for homeowners looking to improve safety around their properties.

One of the hallmark features of the Heath Zenith 598-1306-02 is its advanced motion detection technology. The light is equipped with a passive infrared (PIR) sensor that can detect movement from people or animals in its vicinity. The sensor typically has an adjustable detection range, allowing users to customize how far away motion must occur for the light to activate. This feature is particularly beneficial for ensuring that high-traffic areas such as driveways, porches, and walkways are adequately lit when someone approaches.

In addition to its efficient motion detection capabilities, the Heath Zenith 598-1306-02 offers adjustable brightness settings. This allows users to set the light to a specific brightness level, accommodating various lighting needs. From a subtle glow to brightly illuminating a pathway, users can select the appropriate setting based on their preferences and the surrounding environment.

Another significant characteristic of this outdoor light is its weather-resistant construction. Designed for durability, the Heath Zenith 598-1306-02 can withstand various outdoor conditions, including rain, snow, and extreme temperatures. This ensures that the light remains functional and reliable year-round, enhancing its long-term value.

Moreover, the Heath Zenith 598-1306-02 is built with energy efficiency in mind, utilizing LED technology. LED lights consume significantly less energy compared to traditional incandescent bulbs, resulting in lower electricity bills and a smaller carbon footprint. This eco-friendly approach not only helps save money but also supports sustainability.

Installation is straightforward, thanks to the user's manual guiding users through the process. Whether mounted on walls, ceilings, or eaves, the compact design of the Heath Zenith 598-1306-02 allows it to blend seamlessly with a variety of architectural styles.

Overall, the Heath Zenith 598-1306-02 is an excellent choice for homeowners seeking a reliable and energy-efficient outdoor lighting solution. With its motion detection technology, adjustable brightness settings, durable construction, and energy-saving features, this light delivers on all fronts, making it a smart addition to enhance home safety.
Top Page Image Contents