100 Watt H.P.S.
Dusk-to-Dawn Security Light
Item | Model |
247591 |
Questions or problems? Before returning to your retailer, call our technical service department at
Installation Instructions
With Two Piece Arm
Estimated Installation Time: 60 minutes
Items needed for installation (not included):
•Phillips and flathead screwdrivers
•13 mm, 10 mm, and 8 mm sockets
• | 3/16" Drill bit | • | Drill |
• | Pliers | • | Wire strippers/cutters |
• | Safety glasses | • | Silicone caulk |
• | Ladder | • | Small box or rag |
READ ALL INSTRUCTIONS CAREFULLY BEFORE
BEGINNING INSTALLATION.
NOTE: All wiring must be run in accordance with the National Electrical Code (Canadian Electrical Code in Canada) through conduit or another acceptable means. Contact a qualified electrician if there is any question as to the suit- ability of the system.
Lamp in Fixture Contains Mercury. Dispose According to Local, State, or Federal Laws.
WARNING: Turn power off at the circuit breaker or fuse.
1. | Select a location on a flat wall with structurally sound wood and |
| from 10 to 25 feet (3 to 7.6 m) from the ground. The wood should |
| be at least one inch thick to safely secure the fixture. |
2. | Slide the curved section of the mounting arm into the mounting |
| bracket. Tighten the bolts on the mounting bracket evenly. |
3. | Using the mounting arm and bracket as a guide mark four mount- |
| ing holes. We suggest drilling 3/16" (4.8 mm) pilot holes for the |
| lag screws. |
4. | Mount the arm and bracket using four lag screws and washers |
| provided. |
5. | Place a ring of silicone caulk around mounting arm (see illustra- |
| tion). Slide the straight section of the mounting arm on to the |
| curved section aligning the predrilled holes. |
6. | Secure the two sections with two bolts, nuts and four washers |
| provided. Place silicone caulk on top of the bolts and washers |
| to prevent water from entering. |
7. | Thread your outdoor cable or flexible conduit through the mount- |
| ing arm. |
10.Connect the fixture wires to the service wires using the wire nuts provided (black to black and white to white). Push the connec- tions as far as possible into the straight arm.
11.This fixture must be grounded. Connect the service ground under the head of the green ground screw and secure to the mounting strap.
12.Install the lens/reflector assembly with two screws and washers provided.
13.Screw in the 100 watt H.P. Sodium type S54 bulb provided.
14.Loosen the screw in the center of the photocontrol socket two turns. Twist the socket so that the arrow points north. Note: There is a stop to prevent the socket from turning all the way around. If you have trouble turning the socket, try turning it the other direc- tion. Retighten the screw in the center of the socket.
15.Align the photocontrol (it will only
To test operation during the daytime, cover the photocontrol with a small box or rag. Turn the power on. Light should turn on and reach full brightness within ten minutes. Remove the box or rag to expose the photocontrol to daylight. Light should turn off within two minutes. With the photocontrol exposed, the light will operate automatically – on at dusk and off at dawn.
Photocontrol
Mounting
Arm
Silicone
Caulk
Mounting Strap
Ground
Screw
Lens/Reflector
Assembly
Lag Screw (4)
Bulb
Mounting
8. | Loosely connect the mounting strap to the fixture using two bolts |
| provided. |
9. | Slide the fixture on to the mounting arm until the fixture comes |
| to a stop. Secure the fixture to the mounting arm by tightening |
Flat Washer (10)
Bracket
the two mounting strap bolts. |
Package Contents and Fixture Assembly
© 2008 HeathCo LLC |
|
