Manuals / NEC / Communications / Telephone

NEC R1000 manual Installation

Models: R1000

1 110

Download 110 pages 18.54 Kb

Page 31

Xen IPK R1000 Upgrade Procedure for Xen Axis/Master	Xen IPK

Memory Backup Battery (Retains memory for approximately 21 days)

Key Function (KF)/Multifunction (MF) Registration

Installation

Each system must have one CPUI( )-U( ) ETU in the CPU/EXP slot of the basic B64-U23 KSU. Refer to Figure 2-2: CPUI( )-U( ) ETU Switch Settings.

WARNING

If the CPUI( )-U( ) ETU is installed in slots S1~S8, it will be damaged!

Doc. No. 8283 - Release 1.0 September 2003

Figure 2-2:CPUI( )-U( ) ETU Switch Settings

Hardware Description and Specifications for Xen IPK

Chapter 2 – 23

Image 31

NEC R1000 manual Installation

Contents

Xen IPK This page Intentionally Left Blank Preface & Disclaimer Preface & Disclaimer Important Note About this Upgrade Procedure September Table of Contents 13-05 11-2-0413-00 13-04Chapter Xen IPK R1000 Upgrade Procedure for Xen Axis/ MasterChapter Direct Download from the Installed Xen System Only the Xen Axis system can be saved as Xen IPK Basic Chapter Direct Download from the Installed Xen System Upgrade Type Comments Chapter Direct Download from the Installed Xen System Click Hardware Upload When Upload is complete, click Close Chapter Direct Download from the Installed Xen System C T I O N September Only the Xen Axis system can be saved as Xen IPK Basic Upgrade Type Comments September September September For MIFM-U Software Verification for Mifm -U ETU For PRT1-U ETU Software Verification Adding AN Earth Connection B64-U23 KSU Hardware Description and Specifications for Xen IPK ChapterB64-U23 KSU Cpui -U ETU DescriptionInstallation SW3-1 Description Switch SettingsSW1-1 SW1-2 Description SW1-3 DescriptionLED Indications Replacing Memory BackupDescription Flashing Off Description Basic Port Expanded PKU 192-UA Port Key UnitESIB8-U ETU MDF ConnectionsESIE8-U ETU Pin Assignments MJ1 Pin Signal Signal Name Pin ColourMJ2 Pin Signal Signal Name Pin Colour This page Intentionally Left Blank Required Components Features and Specifications For Xen IPKAttendant Transfer Terminal Type¶+BTT Feature Feature Name NumberGeneral Shortcut KeyCall Arrival CAR Keys Restrictions 46/47 001 Feature Feature Name Number Call Appearance CAP KeysBasic Port Expanded To display a stored Caller ID Caller ID IncomingTo return a call to the name/number displayed on the LCD Caller ID Indication Manual OperationRestrictions Scrolling Caller ID with Return CallGeneral September Caller ID Indication disappears Mobile Pay Phone Out of Area Private Data Error Related Features ListSystem Data Name Function Block Order Memory AttendantShortcut Key Line Key Optional Components Dterm Series i Multiline TerminalsD-19Specifications Refer to individual feature for detailsGeneral Button Units TerminalOther Order Memory Attendant Feature Name NumberTerminal Type DTU-type Multiline Terminal MigrationD-20September To change the off-hook ringing volume Electronic Volume ControlTo change the LCD contrast for Multiline Display Terminals To set the handset receiver volume To change the station ringing volumeTo set the speaker volume 46/47 049 Related Feature List Guide to Feature ProgrammingTo answer using a Multiline Terminal To originate using a Multiline TerminalExternal Zone Paging Meet-Me E-6 To answer using a Single Line Telephones To originate using a Single Line TelephonesSystem Data Name Function Block 46/47 074 ~ 081Full Duplex Handsfree To use the HFU-UA using an DTU--type Multiline Terminal¶+BTM HFU Selection Not applicable Data Assignment ISDN-BRI Trunk ConnectionsGeneral Xen IPK Expanded RestrictionsOrder System Data Name CO Line ServiceOrder Memory System Data Name Function Calling Party Number CPN ServiceISDN-PRI Trunk Connections Terminal Type Not applicable Data Assignment for ISDN-PRI InstallationData Assignment for did Line Services Data Assignment for CO Line ServicesData Assignments for Caller ID Calling Party Number CPN General Xen IPK Expanded Isdn PRI Installation System Data Name Function Did Line ServiceCalling Party Number CPN Presentation from Station Music on Hold Example Guide to Feature Programming Using a Single Line Telephone with a call in progress Using a Multiline Terminal with a call in progressStation Transfer Direct Station Selection DSS Not applicable Universal SlotsPackage PRT4 4 ports, 4 B channels z PRT8 8 ports, 8 B channels Maximum Capacities Station Interface Units Description IPT4-U ETU installed as a COI/COID4-U ETU Other ETUs NO. Maximum NO.ESI8 ETUs Gruide to Feature Programming Programming + BK SettingsGeneral Description DisplayRelated Programming Programming ProceduresPRI Channel Assignment + AN Settings+ AN PRT B Channel Outgoing Priority SelectionPRT B Channel-to-Trunk Group Assignment + BCT Trunk-to-MOH Trunk AssignmentMultiline Terminal Type Selection + BTM Programming Procedures50, Multiline Terminal Type Selection Draft 3 MOH or Ring Back Tone Selection 66, MOH or Ring Back Tone Selection Draft 3 + BTT LCD Line Key Name Assignment68, LCD Line Key Name Assignment Draft 3 + BS Card Interface Slot AssignmentCard Interface Slot Assignment Draft 3 Draft Card Interface Slot Assignment ACD+/CMS/FMS/VMS KSU Power-Based ETU Quantity LimitationsEXP KTU Card Interface Slot AssignmentMIF ACD Assignment This page Intentionally Left Blank