Manuals / NEC / Communications / Telephone

NEC R1000 manual Important Note About this Upgrade Procedure

Models: R1000

1 110

Download 110 pages 18.54 Kb

Page 5

Important Note About this Upgrade Procedure

This document provides all of the necessary information to upgrade your Xen Axis/Master system to Xen IPK Release 1000 software and to install the related hardware.

This document is not intended as replacement pages for your current manuals. However, it can be used to supplement those manuals.

September 2003

Doc. No. 8283 - Release 1.0

Xen IPK R1000 Upgrade Procedure for Xen Axis/Master

iii

Image 5

NEC R1000 manual Important Note About this Upgrade Procedure

Contents

Xen IPK This page Intentionally Left Blank Preface & Disclaimer Preface & Disclaimer Important Note About this Upgrade Procedure September Table of Contents 13-00 11-2-0413-04 13-05Chapter Xen IPK R1000 Upgrade Procedure for Xen Axis/ MasterChapter Direct Download from the Installed Xen System Only the Xen Axis system can be saved as Xen IPK Basic Chapter Direct Download from the Installed Xen System Upgrade Type Comments Chapter Direct Download from the Installed Xen System Click Hardware Upload When Upload is complete, click Close Chapter Direct Download from the Installed Xen System C T I O N September Only the Xen Axis system can be saved as Xen IPK Basic Upgrade Type Comments September September September For MIFM-U Software Verification for Mifm -U ETU For PRT1-U ETU Software Verification Adding AN Earth Connection B64-U23 KSU Hardware Description and Specifications for Xen IPK ChapterB64-U23 KSU Cpui -U ETU DescriptionInstallation SW1-1 SW1-2 Description Switch SettingsSW1-3 Description SW3-1 DescriptionDescription Flashing Off Replacing Memory BackupLED Indications Description Basic Port Expanded PKU 192-UA Port Key UnitESIB8-U ETU MDF ConnectionsESIE8-U ETU Pin Assignments MJ1 Pin Signal Signal Name Pin ColourMJ2 Pin Signal Signal Name Pin Colour This page Intentionally Left Blank Attendant Transfer Features and Specifications For Xen IPKTerminal Type Required ComponentsGeneral Feature Feature Name NumberShortcut Key ¶+BTTCall Arrival CAR Keys Restrictions Basic Port Expanded Feature Feature Name Number Call Appearance CAP Keys46/47 001 To return a call to the name/number displayed on the LCD Caller ID IncomingTo display a stored Caller ID Caller ID Indication Manual OperationRestrictions Scrolling Caller ID with Return CallGeneral September Caller ID Indication disappears Mobile Pay Phone Out of Area Private Data Error Related Features ListShortcut Key Line Key Order Memory AttendantSystem Data Name Function Block Optional Components Dterm Series i Multiline TerminalsD-19Specifications Refer to individual feature for detailsGeneral Other TerminalButton Units Order Memory Attendant Feature Name NumberTerminal Type DTU-type Multiline Terminal MigrationD-20September To change the LCD contrast for Multiline Display Terminals Electronic Volume ControlTo change the off-hook ringing volume To set the speaker volume To change the station ringing volumeTo set the handset receiver volume 46/47 049 Related Feature List Guide to Feature ProgrammingExternal Zone Paging Meet-Me E-6 To originate using a Multiline TerminalTo answer using a Multiline Terminal To answer using a Single Line Telephones To originate using a Single Line TelephonesSystem Data Name Function Block 46/47 074 ~ 081Full Duplex Handsfree To use the HFU-UA using an DTU--type Multiline Terminal¶+BTM HFU Selection Not applicable Data Assignment ISDN-BRI Trunk ConnectionsGeneral Xen IPK Expanded RestrictionsOrder System Data Name CO Line ServiceOrder Memory System Data Name Function Calling Party Number CPN ServiceISDN-PRI Trunk Connections Terminal Type Not applicable Data Assignment for ISDN-PRI InstallationData Assignments for Caller ID Calling Party Number CPN Data Assignment for CO Line ServicesData Assignment for did Line Services General Xen IPK Expanded Isdn PRI Installation System Data Name Function Did Line ServiceCalling Party Number CPN Presentation from Station Music on Hold Example Guide to Feature Programming Station Transfer Using a Multiline Terminal with a call in progressUsing a Single Line Telephone with a call in progress Direct Station Selection DSS Package Universal SlotsNot applicable PRT4 4 ports, 4 B channels z PRT8 8 ports, 8 B channels Maximum Capacities Station Interface Units Description IPT4-U ETU installed as a COI/COID4-U ETU ESI8 ETUs NO. Maximum NO.Other ETUs Gruide to Feature Programming Programming General Description SettingsDisplay + BKRelated Programming Programming ProceduresPRI Channel Assignment + AN Settings+ AN PRT B Channel Outgoing Priority SelectionPRT B Channel-to-Trunk Group Assignment + BCT Trunk-to-MOH Trunk AssignmentMultiline Terminal Type Selection + BTM Programming Procedures50, Multiline Terminal Type Selection Draft 3 MOH or Ring Back Tone Selection 66, MOH or Ring Back Tone Selection Draft 3 + BTT LCD Line Key Name Assignment68, LCD Line Key Name Assignment Draft 3 + BS Card Interface Slot AssignmentCard Interface Slot Assignment Draft 3 Draft Card Interface Slot Assignment ACD+/CMS/FMS/VMS KSU Power-Based ETU Quantity LimitationsEXP KTU Card Interface Slot AssignmentMIF ACD Assignment This page Intentionally Left Blank