Hitachi 308640 manual Accessories

Accessories

Use Only Genuine Graco Parts and Accessories

Grounding Clamp and Wire 222011

12 ga, 25 ft (7.6 m) wire

High Pressure Ball Valves, Viton￿ Seals

5000 psi (35 MPa, 350 bar) Maximum Working Pressure Can be used as fluid drain valve.

210657	1/2 npt(m)
210658	3/8 npt(m)
210659	3/8 x 1/4 npt(m)

In-line Fluid Filter 210500

5000 psi (35 MPa, 350 bar) Maximum Working Pressure

100 mesh. Fits onto the gun's fluid connector. 1/4±18 npsm. Includes the parts shown below.

210501	168517
	Filter

205264

164075

Ruby-ball Needle Assembly 236678

Use to decrease wear with acid catalyzed finishes. For use in place of the standard fluid needle, part no. 238754, item 101 on page 19. Use with diffuser-seat 238427 only.

Plastic Needle Kit 240679

4000 psi (28 MPa, 280 bar) Maximum Working Pressure Includes: Plastic Ball Tipped Needle Assembly 240678, diffuser-seat, and gasket.

For use with acid catalyzed finishes and for light viscosity fluids. Use with diffuser-seat 224855 only. Not recommended for use with AA RAC tips.

Bleed-type Master Air Valve

300 psi (2.1 MPa, 21 bar) Maximum Working Pressure Relieves air trapped in the air line between the pump air inlet and this valve when closed.

107141 3/4 npt(m x f) inlet & outlet

107142 1/2 npt(m x f) inlet & outlet

Air Line Quick-disconnect 113367

Consists of:

113410 Coupling, female, quick-disconnect

113368 Coupling, male, quick-disconnect

Brush 101892

For cleaning the gun.

Fluid Swivel Connector 189018

5800 psi (40 MPa, 400 bar) Maximum Working Pressure To ease movement of the gun and fluid hose. 1/4±18 npsm

Air Whip Hoses

100 psi (0.7 MPa, 7 bar) Maximum Working Pressure To ease movement of the gun and hose. 1/4±18 npsm, polyurethane with SST braid.

238759 3 ft. (0.92 m) hose

236873 6 ft. (1.83 m) hose

Air Cap Verification Kit 239897

For air cap 239898 only, to determine air pressure behind the air cap. Do not use for actual spraying. To be compliant, atomizing air pressure must not exceed 10 psi (70 kPa, 0.7 bar).

Conversion Kits

Kits to convert from a gun with standard spray tip, tip guard, and air cap to a gun with the AA RAC assem- bly. See parts list and drawing below for parts included with kit.

240462 Use with gun part no. 238402 and 238852 to convert to gun part no. 238851.

240463 Use with gun part no. 238883 to convert to gun part no. 239001.

Ref.
No.	Part No.	Description	Qty.
1	238701	AA RAC AIR CAP ASSEMBLY	1
2	192096	RAC HOUSING	1
3	242XXX	TIP CYLINDER; tip of choice
		Includes item 3a	1
3a	193000	S FLUID SEAT	1
4	239172	DIFFUSER-SEAT; Included with Kit
		240462 only	1
	239173	DIFFUSER-SEAT, hi-flow; Included
		with Kit 240463 only	1
5	187521	GASKET, fluid; acetal homopolymer
		(black)	1

5

4

3a

2

1

3

06765B

308640 27