Hitachi 32HDX60 important safety instructions Accessories, Time, First

ACCESSORIES

Check to make sure you have the following accessories before disposing of the packing material.

	REMOTE				“AA” BATTERIES	POWER CORD		MONITOR		IR MOUSE
	CONTROL							CONNECTION CABLE		CABLE
USE		3
	2
	1		6		3.
		5
	4		9
		8
	7	0
					“AAA”BATTERIES
TIME				CH
		VOL
FIRST				1.	4.		5.		6.	7.
	SIMPLE REMOTE				SPEAKER ACCESSORIES		SPEAKER ACCESSORIES		WALL MOUNT UNIT WM50
	CONTROL				(42”)		(50”)		(OPTIONAL)
	CH			H
			ECT	VC
				FA
		SEL
				T
				AN
	-
	VOL		-
			CH	IT
		TE		EX
		MU	U
			MEN
				ER
				POW
				2.		8.		9.		10.
	PDP TV STAND (OPTIONAL) 50STD3 T Table Top Stand Subwoofer Cable Cleaning Cloth									AVC Stand
					C					Accessories
					B
					A
					C«
					B«
					A«	C
						B
						A
						C«
						B«
						A«
	11.				12.		13.	14.		15.

CAUTION: 1. The plasma display wall mount unit WM50 is for use only with Hitachi model 32HDX60, 42HDX60 and 50HDX60.

2. Ceiling mounting is not recommended. Mounting the panel on the ceiling does not provide adequate ventilation for the electronics or proper support for the front glass panel. This plasma television product is designed for a maximum tilting angle of 45 degrees from vertical.

3.This SPD321 PDP stand for use only with Hitachi 32HDX60. Use with other apparatus is capable of resulting in instability causing possible injury.

4.This SPD421 PDP stand for use only with Hitachi 42HDX60 Use with other apparatus is capable of resulting in instability causing possible injury.

5.This 50STD3 T stand for use only with Hitachi 50HDX60. Use with other apparatus is capable of resulting in instability causing possible injury. See important marking located on bottom of stand.

1.Remote Control Unit CLU-5726TSI (P# HL01826). 8. Speaker Accessories (42” only) (P#GM01196).

2.	Simple Remote Control Unit CLU-120S (P#HL01861).			9.	Speaker Accessories (50” only) (P#GM01234).
3.	Two “AA” size, 1.5V batteries (P# FQ00021).			10.	Wall Mount Unit WM50 (Optional) (P#QX00563).
4.	Two “AAA” size, 1.5V batteries (P# FR00061).			11. 32” Stand (SPD321 P# H520443) (Optional).
5.	Power Cord:				42” Stand (SPD421 P# H520444) (Optional).
		32”/42”	50”
	Plasma Monitor	EV01841	EV01861	12.	50” Table Top Stand (50STD3 T) (P#QD35633).
	AVC	EV01841	EV01841	13.	Sub Woofer Cable (P# VZ11701).
6.	Monitor Connection Cable (P#EW07883).			14.	Cleaning Cloth (P#MS00803).
7.	Two IR Mouse cables (P# EY01641).			15. AVC Stand Accessories (P#QJ01081).

REMOTE CONTROL BATTERY INSTALLATION AND REPLACEMENT

1.Open the battery cover of the remote control by pushing the notched part of the cover with your fingers and pulling the cover off.

2.Insert two new “AA” and “AAA” size batteries for the remote control and simple remote control respectively. When replacing old batteries, push them towards the springs and lift them out.

3.Match the batteries to the (+) and (-) marks in the battery compartment.

BOTTOM VIEW	BOTTOM VIEW
(Simple Remote Control)	(Remote Control)

Lift up on tab to	Lift up on tab to
remove back cover.	remove back cover.

4. Replace the cover.

CAUTION: Danger of explosion if battery is incorrectly replaced. Replace with the same or equivalent type.

4