USING THE REMOTE TO CONTROL

SET-TOP-BOX/SATELLITE RECEIVER FUNCTIONS

Operating the precoded function for your set-top-box/satellite receiver.

This remote is designed to operate different types of set-top-box/satellite systems. You must first program the remote to match the remote command set of your set-top-box/satellite systems (refer to page 40).

1.Turn ON your set-top-box/satellite systems.

2.Aim the remote control at the front of your set-top-box/satellite systems.

3.Press and release the SET-TOP-BOX (STB) button to switch to set-top-box/satellite pre-coded mode.

4.Hold down the STB button on the remote and enter the two digit preset code that matches your set-top-box/satellite receiver as shown on page 40. The STB button light will flash 3 times if the code was accepted.

5.Aim the remote at the set-top-box/satellite receiver and press the POWER button. The remote will turn off your set-top-box/satel- lite receiver if the correct two digit preset code is entered. When this occurs, the remote control is programmed for your set-top- box/satellite receiver. If the set-top-box/satellite receiver does not turn off, try a different two digit preset code.

6.The remote will now control your set-top-box/satellite receiver.

NOTES:

1.If your set-top-box/satellite receiver cannot be operated after performing the above procedures, your set-top- box/satellite receiver code has not been precoded into the remote.

2.In the unlikely event that your set-top-box/satellite receiver cannot be operated after performing the above procedures, please consult your set-top-box/satellite receiver operating guide.

3.The remote control will remember the codes you have programmed until the batteries are removed from the remote control. After replacing the batteries repeat the entire programming procedure as stated above.

4.The ANT button will act as the TV/STB button when in STB mode.

SET-TOP-BOX (STB) button

This button allows the remote to control your satellite receiv- er by setting it to SET-TOP-BOX/SATELLITE mode.

PRECODED SET-TOP-BOX/SATELLITE RECEIVER but- tons

These buttons transmit the chosen precoded set-top- box/satellite codes.

EXCLUSIVE TV buttons

These buttons are for operating the TV.

 

 

POWER

 

 

 

 

 

 

 

TV

VCR

 

 

CBL

 

 

STB

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

SOURCE WIZARD

 

 

 

 

DVD

CD

 

 

PVR

 

 

AMP

 

 

 

 

 

 

 

 

1

 

 

2

 

 

 

3

 

 

 

4

 

 

5

 

 

 

6

 

 

 

7

 

 

8

 

 

 

9

 

 

SLEEP

 

 

0

 

 

 

 

INFO

ANT

TV/RGB

A/V NET

 

ASPECT

VIDEO

 

 

 

 

 

 

 

 

 

 

MENU

 

EXIT

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

VOL

 

SELECT

 

 

 

CH

 

 

 

 

 

 

 

 

 

 

 

 

 

MUTE

LAST

CH

 

 

 

 

VID1

 

 

 

 

 

 

 

VID

5

 

 

 

 

 

 

 

 

 

VID 2

 

VID 3

 

 

VID

4

 

 

 

 

 

 

 

 

 

 

 

 

 

PIP

 

 

SURF

 

 

 

FREEZE

 

 

 

 

 

PIP ACCESS

 

 

 

PIP MODE

 

 

SWAP

 

 

DAY/NIGHT

REC

THE REMOTE CONTROL

MY SATELLITE RECEIVER/STB CODE IS:

NOTE: Refer to instruction manual of the set-top-box/satellite receiver for operation of the buttons exclusively for the set-top- box/satellite receiver.

37

Page 37
Image 37
Hitachi 42HDT50, 50HDT50, 32HDT50 SET-TOP-BOX STB button, Precoded SET-TOP-BOX/SATELLITE Receiver but- tons