Manuals / Hitachi / Computer Equipment / Personal Computer

Hitachi 8000 manual Removing and Replacing the Front Bezel

Models: 8000

1 48

Download 48 pages 36.53 Kb

Page 17

Image 17

Removing and Replacing the Front Bezel

1.Remove/disengage any security devices that prohibit opening the computer.

2.Remove all removable media, such as compact discs or USB flash drives, from the computer.

3.Turn off the computer properly through the operating system, then turn off any external devices.

4.Disconnect the power cord from the power outlet and disconnect any external devices.

CAUTION: Regardless of the power-on state, voltage is always present on the system board as long as the system is plugged into an active AC outlet. You must disconnect the power cord to avoid damage to the internal components of the computer.

5.If the computer is on a stand, remove the computer from the stand and lay the computer down.

6.Remove the computer access panel.

7.Lift up the three tabs on the side of the bezel (1), then rotate the bezel off the chassis (2). Figure 2-4Removing the Front Bezel

ENWW	Removing and Replacing the Front Bezel 11

Page 17

Image 17

Hitachi 8000 manual Removing and Replacing the Front Bezel

Contents

HP Compaq 8000 Elite Ultra-Slim Desktop Business PC Hardware Reference GuideFirst Edition November Document Part Number Hardware Reference GuideHP Compaq 8000 Elite Ultra-Slim Desktop Business PC About This Book ENWW iv About This Book1 Product Features Table of contents2 Hardware Upgrades Appendix A SpecificationsIndex Appendix C Security Lock ProvisionsAppendix D Electrostatic Discharge Standard Configuration Features 1 Product FeaturesTable 1-1 Front Panel Components Front Panel ComponentsTable 1-2 Rear Panel Components Rear Panel ComponentsKeyboard Using the Windows Logo KeyTable 1-3 Keyboard Components Table 1-4 Windows Logo Key Functionsarrow Table 1-4 Windows Logo Key Functions continuedWindows Logo Key + + on numpad Serial Number LocationZooms in Windows Logo Key + - on numpadWarnings and Cautions 2 Hardware UpgradesServiceability Features Connecting the Power Cord Removing the Computer Access Panel 2. Tighten the thumbscrew to secure the access panel Replacing the Computer Access PanelFigure 2-3 Replacing the Computer Access Panel 10 Chapter 2 Hardware UpgradesRemoving and Replacing the Front Bezel 4. Reconnect the power cord and turn on the computer Figure 2-5 Replacing the Front Bezel 2. Replace the access panel12 Chapter 2 Hardware Upgrades To replace the front bezelRemoving a Bezel Blank Changing from Desktop to Tower Configuration DDR3-SDRAM SODIMMs Installing Additional MemorySODIMMs Table 2-1 SODIMM Socket Locations Populating SODIMM Socketson page Installing SODIMMs11. Replace the access panel Figure 2-10 Installing a SODIMM18 Chapter 2 Hardware Upgrades Figure 2-9 Removing a SODIMMRemoving the Existing Optical Drive Replacing the Optical DrivePreparing the New Optical Drive Installing the New Optical Drive6. Reconnect the power cord and turn on the computer Figure 2-13 Installing the Optical Drive 4. Replace the access panel5. If the computer was on a stand, replace the stand ENWWReplacing the Hard Drive Replacing the Hard Drive ENWWFigure 2-18 Sliding the Hard Drive into the Carrier 24 Chapter 2 Hardware UpgradesFigure 2-19 Lowering the Hard Drive and Replacing the Guide Screws ENWW16. Replace the computer access panel Figure 2-20 Installing the Hard Drive Carrier18. Reconnect the power cord and turn on the computer 17. If the computer was on a stand, replace the standInstalling and Removing a Port Cover Table A-1 Specifications A SpecificationsApproximate Weight Power SupplyRated Input Current maximum Table A-1 Specifications continuedB Battery Replacement Type TypeType 11. Reconnect the power cord and turn on the computer 9. Replace the access panel10. If the computer was on a stand, replace the stand ENWWHP/Kensington MicroSaver Security Cable Lock Installing a Security LockC Security Lock Provisions Figure C-2 Installing a Cable with a Port Cover Installed PadlockFigure C-3 Installing a Padlock Installing a Security LockENWW HP Business PC Security Lock34 Appendix C Security Lock Provisions Front Bezel Security 5. If the computer is on a stand, remove the computer from the stand 6. Remove the access panel and front bezelFigure C-8 Retrieving the Front Bezel Security Screw 8. Replace the front bezel10. Replace the access panel Figure C-9 Installing the Front Bezel Security Screw12. Reconnect the power cord and turn on the computer Installing a Security LockGrounding Methods D Electrostatic DischargePreventing Electrostatic Damage Computer Operating Guidelines and Routine Care Cleaning Optical Drive PrecautionsSafety Shipping PreparationIndex