Manuals / Hitachi / Computer Equipment / Personal Computer

Hitachi 8000 manual Preparing the New Optical Drive, Installing the New Optical Drive

Models: 8000

1 48

Download 48 pages 36.53 Kb

Page 26

Preparing the New Optical Drive

Preparing the New Optical Drive

Before the new optical drive can be used, the release latch must be attached.

1.Peel the backing off the adhesive on the release latch.

2.Without allowing the release latch to touch the optical drive, carefully align the holes on the release latch with the pins on the side of the optical drive. Make sure the release latch is oriented properly.

3.Insert the pin at the front of the optical drive into the hole at the end of the release latch, and press firmly.

4.Insert the second pin, and press the entire release latch firmly to fasten the latch securely to the optical drive.

Figure 2-12Aligning the Release Latch

Installing the New Optical Drive

NOTE: If you are installing an optical drive in a bay that did not previously have a drive in it, you must remove the access panel and the bezel blank covering the opening of the bay before proceeding. Follow the procedures in Removing the Computer Access Panel on page 9 and Removing a Bezel Blank on page 13.

1.Attach the release latch to the new optical drive. Refer to Preparing the New Optical Drive on page 20.

2.With the back of the optical drive facing the computer and the release latch on the inner side of the drive, align the drive with the opening in the front bezel.

20 Chapter 2 Hardware Upgrades

ENWW

Image 26

Hitachi 8000 manual Preparing the New Optical Drive, Installing the New Optical Drive

Contents

Hardware Reference Guide HP Compaq 8000 Elite Ultra-Slim Desktop Business PCFirst Edition November Document Part Number Hardware Reference GuideHP Compaq 8000 Elite Ultra-Slim Desktop Business PC About This Book iv About This Book ENWW2 Hardware Upgrades Table of contents1 Product Features Appendix A SpecificationsIndex Appendix C Security Lock ProvisionsAppendix D Electrostatic Discharge 1 Product Features Standard Configuration FeaturesFront Panel Components Table 1-1 Front Panel ComponentsRear Panel Components Table 1-2 Rear Panel ComponentsTable 1-3 Keyboard Components Using the Windows Logo KeyKeyboard Table 1-4 Windows Logo Key FunctionsTable 1-4 Windows Logo Key Functions continued arrowZooms in Serial Number LocationWindows Logo Key + + on numpad Windows Logo Key + - on numpadWarnings and Cautions 2 Hardware UpgradesServiceability Features Connecting the Power Cord Removing the Computer Access Panel Figure 2-3 Replacing the Computer Access Panel Replacing the Computer Access Panel2. Tighten the thumbscrew to secure the access panel 10 Chapter 2 Hardware UpgradesRemoving and Replacing the Front Bezel 12 Chapter 2 Hardware Upgrades Figure 2-5 Replacing the Front Bezel 2. Replace the access panel4. Reconnect the power cord and turn on the computer To replace the front bezelRemoving a Bezel Blank Changing from Desktop to Tower Configuration DDR3-SDRAM SODIMMs Installing Additional MemorySODIMMs Populating SODIMM Sockets Table 2-1 SODIMM Socket LocationsInstalling SODIMMs on page18 Chapter 2 Hardware Upgrades Figure 2-10 Installing a SODIMM11. Replace the access panel Figure 2-9 Removing a SODIMMReplacing the Optical Drive Removing the Existing Optical DriveInstalling the New Optical Drive Preparing the New Optical Drive5. If the computer was on a stand, replace the stand Figure 2-13 Installing the Optical Drive 4. Replace the access panel6. Reconnect the power cord and turn on the computer ENWWReplacing the Hard Drive ENWW Replacing the Hard DriveFigure 2-19 Lowering the Hard Drive and Replacing the Guide Screws 24 Chapter 2 Hardware UpgradesFigure 2-18 Sliding the Hard Drive into the Carrier ENWW18. Reconnect the power cord and turn on the computer Figure 2-20 Installing the Hard Drive Carrier16. Replace the computer access panel 17. If the computer was on a stand, replace the standInstalling and Removing a Port Cover Approximate Weight A SpecificationsTable A-1 Specifications Power SupplyTable A-1 Specifications continued Rated Input Current maximumB Battery Replacement Type TypeType 10. If the computer was on a stand, replace the stand 9. Replace the access panel11. Reconnect the power cord and turn on the computer ENWWHP/Kensington MicroSaver Security Cable Lock Installing a Security LockC Security Lock Provisions Figure C-3 Installing a Padlock PadlockFigure C-2 Installing a Cable with a Port Cover Installed Installing a Security LockENWW HP Business PC Security Lock34 Appendix C Security Lock Provisions Front Bezel Security Figure C-8 Retrieving the Front Bezel Security Screw 6. Remove the access panel and front bezel5. If the computer is on a stand, remove the computer from the stand 8. Replace the front bezel12. Reconnect the power cord and turn on the computer Figure C-9 Installing the Front Bezel Security Screw10. Replace the access panel Installing a Security LockGrounding Methods D Electrostatic DischargePreventing Electrostatic Damage Computer Operating Guidelines and Routine Care Safety Optical Drive PrecautionsCleaning Shipping PreparationIndex