Manuals / Hitachi / Computer Equipment / Personal Computer

Hitachi 8000 manual 9 Removing a SODIMM, 10 Installing a SODIMM, Replace the access panel, Enww

Models: 8000

1 48

Page 24

8.If you are adding a second SODIMM, remove the SODIMM from the top XMM1 socket to access the bottom XMM3 socket. Press outward on the two latches on each side of the SODIMM (1) then pull the SODIMM out of the socket (2).

Figure 2-9Removing a SODIMM

9.Slide the new SODIMM into the socket at approximately a 30° angle (1) then press the SODIMM down (2) so that the latches lock it in place.

Figure 2-10Installing a SODIMM

NOTE: A memory module can be installed in only one way. Match the notch on the module with the tab on the memory socket.

A SODIMM must occupy the XMM1 (top) socket.

10.Replace the SODIMM in the XMM1 socket if it was removed.

11.Replace the access panel.

18 Chapter 2 Hardware Upgrades

ENWW

Page 24

Image 24

Hitachi 8000 9 Removing a SODIMM, 10 Installing a SODIMM, A SODIMM must occupy the XMM1 top socket, Hardware Upgrades

Contents

Hardware Reference Guide HP Compaq 8000 Elite Ultra-Slim Desktop Business PCHardware Reference Guide HP Compaq 8000 Elite Ultra-Slim Desktop Business PCFirst Edition November Document Part Number About This Book iv About This Book ENWWTable of contents 1 Product Features2 Hardware Upgrades Appendix A SpecificationsAppendix C Security Lock Provisions Appendix D Electrostatic DischargeIndex 1 Product Features Standard Configuration FeaturesFront Panel Components Table 1-1 Front Panel ComponentsRear Panel Components Table 1-2 Rear Panel ComponentsUsing the Windows Logo Key KeyboardTable 1-3 Keyboard Components Table 1-4 Windows Logo Key FunctionsTable 1-4 Windows Logo Key Functions continued arrowSerial Number Location Windows Logo Key + + on numpadZooms in Windows Logo Key + - on numpad2 Hardware Upgrades Serviceability FeaturesWarnings and Cautions Connecting the Power Cord Removing the Computer Access Panel Replacing the Computer Access Panel 2. Tighten the thumbscrew to secure the access panelFigure 2-3 Replacing the Computer Access Panel 10 Chapter 2 Hardware UpgradesRemoving and Replacing the Front Bezel Figure 2-5 Replacing the Front Bezel 2. Replace the access panel 4. Reconnect the power cord and turn on the computer12 Chapter 2 Hardware Upgrades To replace the front bezelRemoving a Bezel Blank Changing from Desktop to Tower Configuration Installing Additional Memory SODIMMsDDR3-SDRAM SODIMMs Populating SODIMM Sockets Table 2-1 SODIMM Socket LocationsInstalling SODIMMs on pageFigure 2-10 Installing a SODIMM 11. Replace the access panel18 Chapter 2 Hardware Upgrades Figure 2-9 Removing a SODIMMReplacing the Optical Drive Removing the Existing Optical DriveInstalling the New Optical Drive Preparing the New Optical DriveFigure 2-13 Installing the Optical Drive 4. Replace the access panel 6. Reconnect the power cord and turn on the computer5. If the computer was on a stand, replace the stand ENWWReplacing the Hard Drive ENWW Replacing the Hard Drive24 Chapter 2 Hardware Upgrades Figure 2-18 Sliding the Hard Drive into the CarrierFigure 2-19 Lowering the Hard Drive and Replacing the Guide Screws ENWWFigure 2-20 Installing the Hard Drive Carrier 16. Replace the computer access panel18. Reconnect the power cord and turn on the computer 17. If the computer was on a stand, replace the standInstalling and Removing a Port Cover A Specifications Table A-1 SpecificationsApproximate Weight Power SupplyTable A-1 Specifications continued Rated Input Current maximumB Battery Replacement Type TypeType 9. Replace the access panel 11. Reconnect the power cord and turn on the computer10. If the computer was on a stand, replace the stand ENWWInstalling a Security Lock C Security Lock ProvisionsHP/Kensington MicroSaver Security Cable Lock Padlock Figure C-2 Installing a Cable with a Port Cover InstalledFigure C-3 Installing a Padlock Installing a Security LockHP Business PC Security Lock 34 Appendix C Security Lock ProvisionsENWW Front Bezel Security 6. Remove the access panel and front bezel 5. If the computer is on a stand, remove the computer from the standFigure C-8 Retrieving the Front Bezel Security Screw 8. Replace the front bezelFigure C-9 Installing the Front Bezel Security Screw 10. Replace the access panel12. Reconnect the power cord and turn on the computer Installing a Security LockD Electrostatic Discharge Preventing Electrostatic DamageGrounding Methods Computer Operating Guidelines and Routine Care Optical Drive Precautions CleaningSafety Shipping PreparationIndex