Connection to the control signal terminal (continued)
|
|
|
| Control data table | ||
|
|
|
|
|
| |
Item |
|
|
|
| Data code | |
|
| |||||
MOUSE | 00h=stop mouse emulation. 01~7Fh=start mouse emulation | |||||
|
|
| ||||
COMMUNICATE | 0Xh=8N1, 1Xh=7N1 |
| ||||
X0h=1200bps, X1h=2400bps, X2h=4800bps, X3h=9600bps, X4h=19200bps | ||||||
| ||||||
|
| |||||
POWER | 3Eh=Power off (Standby mode), 3Fh=Power on | |||||
|
| |||||
MIRROR | 00h=Normal, 01h=H:Invert, 02h=V:Invert, 03h=H&V:Invert | |||||
|
| |||||
INPUT | 11h=VIDEO, 21h=RGB1, 22h=RGB2 | |||||
|
|
| ||||
VIDEO SYSTEM | 00h | 00h=Auto, 00h 01h=NTSC, 00h 04h=NTSC4.43 | ||||
00h | 02h=PAL, 00h 03h=SECAM, 00h | |||||
| ||||||
|
|
|
| |||
VOLUME | 00h | (min) ~ 24h (max) |
| |||
|
|
| ||||
MUTE | 00h=Mute off, 01h=Mute on |
| ||||
|
|
|
|
| ||
BRIGHT | 00h | 00h | 00h | (dark) ~ 00h 00h 24h (brite) | ||
|
|
|
|
| ||
CONTRAST | 00h | 00h | 00h | (lower) ~ 00h 00h 24h (higher) | ||
|
|
|
|
| ||
COLOR | 00h | 00h | 00h | (less) ~ 00h 00h 24h (more) | ||
|
|
|
|
| ||
TINT | 00h | 00h | 00h | (red) ~ 00h 00h 24h (green) | ||
|
|
|
|
| ||
SHARPNESS | 00h | 00h | 00h | (soft) ~ 00h 00h 24h (sharp) | ||
|
|
|
|
|
| |
H. PHASE | 00h | 00h | 00h | ~ 00h 00h 1Fh |
| |
|
|
|
| |||
H. POSIT | 00h | 00h | 4Fh 00h (left) ~ 00h 00h 17h 05h (right) | |||
|
|
|
|
| ||
H. SIZE | 00h | 00h | 06h | 06h (narrow) ~ 00h 00h 04h 0Ch (wide) | ||
|
|
|
|
| ||
V. POSIT | 00h | 00h | 03h | 00h (down) ~ 00h 00h 00h 06h (up) | ||
|
|
|
|
| ||
COLOR BALANCE | 00h | 00h | 00h | (for Red) ~ 00h 00h 24h (for Blue) | ||
|
|
|
| |||
AUTO ADJUST | 00h | (start) , 07h (stop) |
| |||
|
|
| ||||
| 0Xh=Blank off, 1Xh=Blank on |
| ||||
BLANK | bit0 0=Blue off, 1=Blue on, | bit1 0=Green off, 1=Green on | ||||
| bit2 0=Red off, 1=Red on, | bit3 0=Not change, 1=change | ||||
|
| |||||
REVEAL | X1h=Reveal down, X4h=Reveal right, X=0 (slow) ~ 7 (fast) | |||||
(1)Circuit codes when ask code and default set code are issued (Number of data byte=1)
00h=normal display, 01h=magnified display
(2)When magnification is set by setting codes (Number of data bytes=6)
| 1st, 2nd data bytes: magnification starting positions in horizontal direction (left end) | ||
MAGNIFY | 00h | 00h | (left) ~ 3Ch 05h (right) |
| 3rd, 4th data bytes: magnification starting positions in vertical direction (top) | ||
| 00h | 00h | (top) ~ 0Dh 04h (bottom) |
| 5th, 6th data bytes: Horizontally magnified dot number data | ||
| 64h | 00h | (large) ~ 20h 06h (small) |
|
| ||
FREEZE | 00h=normal display, 01h=still picture display | ||
ENGLISH
Caution If computer sends the undefined command code or data code, Projector can not guarantee operation.
Command is consisted of 2 command bytes and following data bytes.
'0xH' : | Projector sends to computer. |
'1xH' : Command reply | Projector sends to computer. |
'2xH' : Ask command | Computer sends to Projector. |
'3xH' : Set command | Computer sends to Projector. |
'4xH' : Default set command | Computer sends to Projector |
'5xH' - 'FxH' : Reserved |
|
'x' indicates the length of data bytes. |
|
25 | |
Data table shows the data byte. |
Downloaded from www.Manualslib.com manuals search engine
