HOW to USE, Selecting the driver bit | Hitachi DH 30PB, DH 30PC

English

(When using dust collector (B) attached to a drill bit that has more than 7-15/ 32" (190 mm) of overall length, dust collector (B) cannot touch the concrete surface but rotates. Therefore please use dust collector (B) by attaching to drill bits which have 6-17/32" (166 mm), 6-19/64" (160 mm) and 4-21/64" (110 mm) overall length.

◯Dump particles after every two or three holes when drilling.

◯Please replace the drill bit after removing dust collector (B).

8.Selecting the driver bit

Screw heads or bits will be damaged should an inappropriate bit for the screw diameter be employed to drive in the screws.

9.Selecting the function mode

You can switch functions to the 3 modes of “strike only, “rotation + strike”, and “rotation only” by turning the change lever while pressing the push button. Set the mark position of the change lever to that of the mode to be used.

CAUTION:

◯Before operating the change lever, check and make sure that the motor has stopped.

A failure can occur if it is operated while the motor is running.

◯If the change lever does not move up to the mark position of each mode, carry out switching while turning the grip end to left and right. Also, it can become difficult to change the mode at low temperature, and therefore perform warming-up.

◯To operate the change lever, press the push button, and release the lock of the change lever. Also, check and make sure after operation that the push button has returned and that the change lever has been locked.

◯Switch the change lever without mistake. If it is used at a position halfway, there is a fear that the service life of the switching mechanism may be shortened.

◯Note that it is impossible to switch from “rotation only” to “strike only” or from “strike only” to “rotation only”. Switch over via “rotation + strike”. (DH30PC)

HOW TO USE

CAUTION:

◯To prevent accidents, make sure to turn the switch off and disconnect the plug from the receptacle when the drill pits and other various parts are installed or removed. The power switch should also be turned off during a work break and after work.

12

Image 12

Hitachi DH 30PB, DH 30PC instruction manual HOW to USE, Selecting the driver bit, Selecting the function mode

Contents

Avertissement Advertencia Contents Important Safety Information Meanings of Signal Words Safety General Safety Rules English Specific Safety Rules and Symbols Never operate without all guards in place Blades and accessories must be securely mounted to the tool Make Them Available to Other Users Owners of this Tool Double Insulation for Safer Operation Specifications Functional DescriptionName of Parts Assembly and Operation ApplicationsPrior to Operation Installation of dust cup or dust Collector B Optional accessoriesConfirming condition of the environment Mounting the drill bit Fig HOW to USE Selecting the function modeSelecting the driver bit Switch operation Rotation + StrikingRotation only When driving machine screws Fig When driving wood screws Fig Using the stopper Fig Striking only DH30PC HOW to USE the Core BIT for Light Load Using the side handle How to bore Fig Dismounting. Fig Maintenance and Inspection Maintenance of the motorInspecting the drill bits Inspecting the screws How to replase grease Service and repairsPage Page Page Page Page Page Informations Importantes DE Sécurité Signification DES Mots D’AVERTISSEMENT Securite Regles Generale DE SecuriteConserver CES Instructions Français Regles DE Securite Specifiques ET Symboles NE Jamais toucher les parties mobiles Utiliser l’outil correct Ne pas essuyer les parties en plastique avec du solvant Double Isolation Pour UN Fonctionnement Plus SUR Description Fonctionnelle NOM DES Parties Avant L’UTILISATION Source d’alimentationInterrupteur d’alimentation Cordon prolongateur Vérification des conditions d’environnement Montage du foret de perçage Fig Sélection du mode de fonction Sélection de la mèche pour visseuse Utilisation Fonctionnement de l’interrupteurRotation + frappe Rotation seulement Lors du vissage des vis machine Fig Enfoncement de vis à bois Fig Percussion uniquement DH30PC Utilisation de l’arràtoir Fig Utilisation de la poignée latérale Montage Perçage Fig Démontage Fig Contrôle du foret de perçage Inspection des visEntretien du moteur Contrôle des balais en carbone Fig Comment remplacer la graisse Entretien et reparation Français Page Page Page Page Page Información Importante Sobre Seguridad Significado DE LAS Palabras DE Señalización Seguridad Normas Generales DE SeguridadGuarde Estas Instrucciones Español Normas Y Símbolos Específicos DE Seguridad No toque Nunca las piezas móviles Maneje con cuidado las herramientas eléctricas Aislamiento Doble Para Ofrecer UNA Operación MÁS Segura Descripción Funcional NomenclaturaEspecificaciones Montaje Y Operación AplicacionesAntes DE LA Operación Confirme las condiciones del medio ambiente Montaje de la broca Fig Como SE USA Selección de la broca destornilladorSelección del modo de función Operación del conmutador Rotación + golpeteoRotación solamente Español Atornillando tornillos para madera Fig Percusión solamente DH30PCModo de usar el tope Fig Modo DE Usar LA Barrena Tubularpara Cargas Ligeras Uso del asa lateral Montaje Modo de taladrar Fig Desmontaje Fig Mantenimiento E Inspección Inspeccionar la broca de taladroInspección de los tornillos Mantenimiento de motor Cambio de grasa Mantenimiento y reparaciónPage Page Page Page Page Page Hitachi Koki Canada Co