APPLICATIONS
Rotation and hammering function
◯Drilling anchor holes
◯Drilling holes in concrete
◯Drilling holes in tile Rotation only function
◯Drilling in steel or wood (with optional accessories)
◯Tightening machine screws, wood screws (with optional accessories)
PRIOR TO OPERATION
1.Power source
Ensure that the power source to be utilized conforms to the power requirements specified on the product nameplate.
2.Power switch
Ensure that the power switch is in the OFF position. If the plug is connected to a power receptacle while the power switch is in the ON position, the power tool will start operating immediately, which could cause a serious accident.
3.Extension cord
When the work area is removed from the power source, use an extension cord of sufficient thickness and rated capacity. The extension cord should be kept as short as practicable.
4.Mounting the drill bit (Fig. 1)
CAUTION
To prevent accidents, make sure to turn the switch off and disconnect the plug from the receptacle.
NOTE
When using tools such as bull points, drill bits, etc., make sure to use the genuine parts designated by our company.
(1)Clean the shank portion of the drill bit.
(2)Insert the drill bit in a twisting manner into the tool holder until it latches itself (Fig. 1).
(3)Check the latching by pulling on the drill bit.
(4)To remove the drill bit, fully pull the grip in the
direction of the arrow and pull out the drill bit (Fig. 2).
5.Installation of dust cup or dust collector (B) (Optional accessories) (Fig. 3, Fig. 4)
When using a rotary hammer for upward drilling operations attach a dust cup or dust collector (B) to collect dust or particles for easy operation.
◯Installing the dust cup
Use the dust cup by attaching to the drill bit as shown in Fig. 3.
When using a bit which has big diameter, enlarge the center hole of the dust cup with this rotary hammer.
◯Installing dust collector (B)
When using dust collector (B), insert dust collector
(B) from the tip of the bit by aligning it to the groove on the grip (Fig. 4).
CAUTION
◯The dust cup and dust collector (B) are for exclusive use of concrete drilling work. Do not use them for wood or metal drilling work.
◯Insert dust collector (B) completely into the chuck part of the main unit.
◯When turning the rotary hammer on while dust collector (B) is detached from a concrete surface,
dust collector (B) will rotate together with the drill bit. Make sure to turn on the switch after pressing the dust cup on the concrete surface. (When using dust collector (B) attached to a drill bit that has more than 190 mm of overall length, dust collector (B) cannot touch the concrete surface and will rotate. Therefore please use dust collector (B) by attaching to drill bits which have 166 mm, 160 mm, and 110 mm overall length.)
◯Dump particles after every two or three holes when drilling.
◯Please replace the drill bit after removing dust
collector (B).
6.Selecting the driver bit
Screw heads or bits will be damaged unless a bit appropriate for the screw diameter is employed to drive in the screws.
7.Confirm the direction of bit rotation (Fig. 5)
The bit rotates clockwise (viewed from the rear side) by pushing the R-side of the push button.
The L-side of the push button is pushed to turn the bit counterclockwise.
HOW TO USE
CAUTION
To prevent accidents, make sure to turn the switch off and disconnect the plug from the receptacle when the drill pits and other various parts are installed or removed. The power switch should also be turned off during a work break and after work.
1.Switch operation
The rotation speed of the drill bit can be controlled steplessly by varying the amount that the trigger switch is pulled. Speed is low when the trigger switch is pulled slightly and increases as the switch is pulled more. Continuous operation may be attained by pulling the trigger switch and depressing the stopper. To turn the switch OFF, pull the trigger switch again to disengage the stopper, and release the trigger switch to its original position.
2.Rotation + hammering
This rotary hammer can be set to rotation and hammering mode by pressing the push button and
turning the change lever to the 
mark (Fig. 6).
(1)Mount the drill bit.
(2)Pull the trigger switch after applying the drill bit tip to the drilling position (Fig. 7).
(3)Pushing the rotary hammer forcibly is not necessary
at all. Pushing slightly so that drill dust comes out gradually is sufficient.
CAUTION
When the drill bit touches construction iron bar, the bit will stop immediately and the rotary hammer will react to revolve. Therefore grip the side handle and handle tightly as shown in Fig. 7.
3.Rotation only
This rotary hammer can be set to rotation only mode
by pussing the push button and turning the change
lever to the 
mark (Fig. 8).
To drill wood or metal material using the drill chuck and chuck adapter (optional accessories), proceed as follows.
Installing drill chuck and chuck adapter: (Fig. 9)
