English
GENERAL OPERATIONAL PRECAUTIONS
1.Keep work area clean. Cluttered areas and benches invite accidents.
2.Avoid dangerous environment. Don’t expose power tools and charger to rain. Don’t use power tools and charger in damp or wet locations. And keep work area well lit. Never use power tools and charger near flammable or explosive materials. Do not use tool and charger in presence of flammable liquids or gases.
3.Keep children away. All visitors should be kept safe distance from work area.
4.Store idle tools and charger. When not in use, tools and charger should be stored in dry, high or
5.Don’t force tool. It will do the job better and safer at the rate for which it was designed.
6.Use right tool. Don’t force small tool or attachment to do the job of a heavy duty tool.
7.Wear proper apparel. Do not wear clothing or jewelry. They can be caught in moving parts. Rubber gloves and footwears are recommended when working outdoor.
8.Use eye protection with most tools. Also use face or dust mask if cutting operation is dusty.
9.Don’t abuse cord. Never carry charger by cord or yank it to disconnect from receptacle. Keep cord from heat, oil and sharp edges.
10.Secure work. Use clamps or a vise to hold work. It’s safer than using your hand and it frees both hands to operate tool.
11.Don’t overreach. Keep proper footing and balance at all times.
12.Maintain tools with care. Keep tools sharp at all times, and clean for best and safest performance. Follow instructions for lubricating and changing accessories.
13.When the charger is not in use, or when being maintained and inspected, disconnect its power cord from the receptacle.
14.Remove chuck wrenches and wrenches. Form habit of checking to see that wrenches are removed from tool before turning it on.
15.Avoid accidental starting. Don’t carry tool with finger on switch.
16.To avoid danger, always use only the specified charger.
17.Use only genuine HITACHI replacement parts.
18.Do not use power tools for applications other than those specified in the Handling Instructions.
19.To avoid personal injury, use only the accessories or attachment recommended in these handling instructions or in the HITACHI catalog.
20.Let only the authorized service center do the repairing. The Manufacturer will not be responsible for any damages or injuries caused by repair by the unauthorized persons or by mishandling of the tool.
21.To ensure the designed operational integrity of power tools and charger, do not remove installed covers or screws.
22.Always use the charger at the voltage specified on the nameplate.
23.Do not touch movable parts or accessories unless the power source has been disconnected.
24.Always charge the battery before use.
25.Never use a battery other than that specified. Do not connect a usual dry cell, a rechargeable battery other than that specified or a car battery to the power tool.
26.Do not use any transformer that has a booster.
27.Do not charge the battery from an engine electric generator or DC power supply.
28.Always charge indoors. Because the charger and battery heat slightly during charging, charge the battery in a place not exposed to direct sunlight; where the humidity is low and the ventilation is good.
29.Before starting to work in a high place, pay attention to the activities below to make sure there are no people below.
30.Use the exploded assembly drawing on this handling instructions only for authorized servicing.
PRECAUTIONS FOR CORDLESS DRIVER DRILL
1.Always charge the battery at a temperature of 10 – 40°C. A temperature of less than 10°C will result in over charging which is dangerous. The battery cannot be charged at a temperature higher than 40°C. The most suitable temperature for charging is that of 20 – 25°C.
2.When one charging is completed, leave the charger for about 15 minutes before the next charging of battery.
Do not charge more than two batteries consecutively.
3.Do not charge the battery for more than 2 hours. The battery will be fully charged in about 1 hour and charging should be stopped when 1 hour has elapsed from commencement. Disconnect the charger power cord from the receptacle.
4.Do not allow foreign matter to enter the hole for connecting the rechargeable battery.
5.Never disassemble the rechargeable battery and charger.
6.Never
7.Do not dispose of the battery in fire. If the battery is burnt, it may explode.
8.When drilling in wall, floor or ceiling, check for buried electric power cord, etc.
9.Bring the battery to the shop from which it was purchased as soon as the
10.Using an exhausted battery will damage the charger.
11.Do not insert object into the air ventilation slots of the charger.
Inserting metal objects or inflammables into the charger air ventilation slots will result in electrical shock hazard or damaged charger.
12.When mounting a bit into the keyless chuck, tighten the sleeve adequately. If the sleeve is not tight, the bit may slip or come off, causing injury.
3
