Honda Power Equipment HR195PDA .m

I

9. MAINTENANCE ,

SPARK PLUG SERVICE

Recommended spark plugs: $lGK BPR5ES

ND 16EPR-U

CHAMPION RNIZY

r-GET-l Spark plugs of the wrong heat range can cause engine

damage.

l%r good performance, the spark plug must be properly gapped and free of

deposits.

1. Disconnect the spark plug cap, and remove any dir-t from around the spark

plug area.

.m

Touching the engine or exhaust system while hot can

cause burns. Let the engine cool before servicing.

2. Remove the spark plug with a.,spark plug wrench.

3. Inspect the spark plug. Replace it if the electrodes are worn, or if the insulator

is cracked or chipped. Clean the spark plug with a wire brush if you are

going to reuse it. .:

4. Measure the spark plug electrode gap with a,feeler gauge. The gap should

be 0.024-0.028 in (0.6-0.7 mm). Correct the gap as necessary by carefully

bending the side electrode. -

5. Install the spark plug carefully, by hand, to avoid cross-threading.

6. After the spark plug-is seated, tighten with a spark plug wrench to compress

the washer.

II

.A loose spark- plug can get hot enough to damage the

engine. Overtightening may damage the threads.

NOTE: If installing a new spark plug, tighten 1

seats to compress the washer. If reinstalling

1 /8_1/4 turn after the spark plug seats.

7. Install the spark plug cap on the spark plug.

SPARK PLUG

CAP ,,,,f.

I2 turn after the spark plug

a used spark plug; tighten

0.024-0.028 in.

(0.8-0.7 mm)

\

36

SPARK PLUG GRENCH

Contents

Main Page B damage 1 CONTENTS 2 CONTENTS 3 1. SAFETY Read all safety instructions before operating the mower. I DO NOT START UNLESS~REAR DOOR IS CLOSED OR BAG IS IN PLACE. SAFETY INFORMATION Operator Responsibility Blade Hazards Thrown Object Hazards Fire and Burn Hazards Carbon Monoxide Poisoning Hazard IMPORTANT MESSAGE TO PARENTS Page 2. COMPONENT IDENTIFICATION D 9 \ -u., 3. CONTROLS 10 3. CONTROLS CUTTING HEIGHT ADJUSTMENT LEVERS II 4. ATTACHMENTS i GRASS BAG (standard equipment) Installation 12 Rerhval : ., 5. PRE-OPERATION CiiECK BLADE 5. PRE-OPERATION /CHECK 5. PRE-OPERATION CHECK (1 I 5. PRE-OPERATION bHECK 16 5. PRE-OPERATION CHECK 5. PRE-OPERATION bHECK 18 Page Page Page r 6. OPERATION CLEARING A FLOODED ENGINE 22 Page B m, Page HIGH ALTITUDE OPERATION 7. MOWING RECOMMENDATIONS 27 7. MOWING RECOMl/ilENDATIONS 28 7. MOWING RECOMMENDATIONS 29 8. TRANSPORTING , I, .-_ 30 I I I I I I 0 I I I I I I I I ENGINE OIL CHANGE Engine oil capacity: 0.63 US ,qt (0.6 PI FILLERLAP/ 9. MAINTENANCE : 34 I -%f/--- .m B rkn 9. MAINTENANCE : FLYWHEEL BRAKE CABLE ABJUSTMENT 1. 38 Page Page .9. -MAINTENANCE GRASS RAG CLEANING AND REPLACEMENT ,./ 41 9. MAINTENANCE 1 BLADE REMOVAL AND INS+ALLATION . . 42 Blade Removal Blade Installation Blade bolt torque: 36.2-43.4 ft-lb (5.0-6.0 kg-m) I IO. STORAGE 44 Preparation for Storage I Stored lawn clippings are a fire hazard. Always empty the grass bag after use. 10. STORAGE For storage of 1 or 2 months: For storage of more than 2 months: 10. STORAGE I B. 46 10. STORAGE 47 !. 11. TROUBLESHOOTING 48 j ENGINE ( 11. TROUBLESHOOTING GRASS CUTTING 49 GRASS BAGGING VIBRATION I 12. SPECIFICATIONS; MOWER MODELS 50 x DIMENSIONS 13. WARRANTY SERVICE Owner Satisfaction 51 Current customer service contact information: United States, Puerto Rico, and U.S. Virgin Islands: