Manuals / Brands / Computer Equipment / Laptop / Honeywell / Computer Equipment / Laptop

Honeywell 6100 Agency Approvals, Nijverheidsweg, Label Locations, The Netherlands, •1995/5/EC R&TTE, Laser Light Label, 5627 BT Eindhoven, Approvals by Country

1 92

Download 92 pages, 4.84 Mb

1

Agency Approvals

Label Locations

Dolphin 6100 mobile computers meet or exceed the requirements of all applicable standards organizations for safe operation. However, as with any electrical equipment, the best way to ensure safe operation is to operate them according to the agency guidelines that follow. Read these guidelines carefully before using your mobile computer.

Compliance Label

Laser Light Label

Laser Light Label

LASER LIGHT. DO NOT STARE INTO BEAM CLASS 2 LASER PRODUCT

1.0 mW MAX OUTPUT: 650nM IEC 60825-1:1993+A1+A2

Complies with 21 CFR 1040.10 and 1040.11 except for deviations pursuant to Laser Notice No. 50, dated June 24, 2007.

Approvals by Country

Refer to the Honeywell Scanning & Mobility compliance center at www.honeywellaidc.com/compliance to review and download any publicly available documentation pertaining to the certification of this product in a given country.

R&TTE Compliance Statement—802.11b/g and/or BluetoothThe CE marking indicates compliance with the following directives:•1995/5/EC R&TTE•2011/65/EU RoHS (Recast)

In addition, this product complies to 2006/95/EC Low Voltage Directive when supplied with the recommended power supply.

For further information, contact:Hand Held Products Europe B.V.Nijverheidsweg 9-135627 BT EindhovenThe Netherlands

Honeywell shall not be liable for use of our product with equipment (i.e., power supplies, personal computers, etc.) that is not CE marked and does not comply with the Low Voltage Directive.

1 - 1

Contents

Page Disclaimer Trademarks Patents Other Trademarks Chapter 1 - Agency Approvals Chapter 2 - Getting Started Chapter 3 - Terminal Hardware Overview Chapter 4 - Using the Keypad Chapter 5 - Using the Image Engine Chapter 6 - Using the Laser Engine Chapter 7 - Communication Chapter 8 - Bluetooth Handler Chapter 9 - Dolphin HomeBase/eBase Device Chapter 10 - Dolphin 6100 ChargeBase Device (Model 6100-CB-1) Chapter 11 - Dolphin 6100 Net Base Device Chapter 12 - Dolphin QuadCharger Device Chapter 13 - Customer Support Page Agency Approvals Laser Safety Label Laser Eye Safety Statement: LED Safety Statement CB Scheme FCC RF Radiation Exposure Statement This device and its antenna must not be CAUTION Canadian Compliance Honeywell Scanning & Mobility Product Environmental Information Anatel Page Getting Started Step 2. Charge the Batteries a minimum of 4 or 6 hours depending on your battery before initial use 1.Attach the appropriate plug adapter to the plug of the power cable 2.Insert the plug into the appropriate power source Plug the Dolphin power cable into the Desktop Command Bar Icons Icon Meaning ALPHA Keypad Transcriber Using the Stylus Tap Selecting Programs Start Programs Pop-UpMenus Using Windows Explorer Page Terminal Hardware Overview Front Panel Features Scan/Decode LED Note: The LED is user-programmable LED Color Meaning Using Screen Protectors Display Backlight Settings Control Panel Backlight Using Screen Protectors Removing the Screen Protector 1.Press the Power key to put the terminal in Suspend Mode 3.Wipe the screen with a clean, non-abrasive, lint-freecloth Installing Your Screen Protector Page Page Stylus Calibration Recalibrate Back Panel Features Hand Strap Finger Saddle Installed Battery Speaker Left Side Panel Features Side Button Side Door The rubber door on the left side panel provides access to the Micro SD slot Installing Memory Cards Right Side Panel Features Headset Jack Top Panel Features Image Engine Window Bottom Panel Features I/O Connector Dolphin Peripherals/Accessories for the Dolphin Dolphin HomeBase™ Device Dolphin eBase™ Device Dolphin Net Base Device Dolphin QuadCharger™ Device Dolphin USB Communication Cable Changing the Main Battery Pack Checking Battery Power Guidelines for Battery Pack Use and Disposal Charging Hard Reset (Cold Boot) Press and hold the The terminal \Honeywell\Autoinstall Suspend Mode Care and Cleaning of the Dolphin Terminal Dolphin 6100 Technical Specifications Page Using the Keypad Basic Keys Name Function Backspace Control Function Key Combinations CTRL Key Combinations Program Buttons Using the Image Engine 5300 High Density (5300HD) 5 mil 8.3 mil Data 5100 Standard Range (5100SR) 5100 Short Focus (5100SF) 5100 High Density (5100HD) Symbology Type Symbology Name 1D Symbologies 2D Symbologies Composite Codes Activating the Engine Scan Using Demos Demos Scan Demo Sample Bar Codes You can use the following bar codes to verify decoding: Omni-DirectionalScanning Positions Capturing Images (5300 Engine Only) Image Preview High-VisAiming Pattern Page Using the Laser Engine To access these demos, tap Start > Programs > Demos • Select Scan Demo to verify decoding Decoding a Bar Code 1.Tap Start > Demos > Scan Demo Project the aiming beam by pressing and holding the Communication Connecting the USB Charging/Communication Cable ActiveSync Communication Communication Type USB Hardware Requirements for Setup Software Requirements for Communication Setting Up the Host Workstation Connection Settings Allow USB connections Change Connection Communicating with the Dolphin Terminal Synchronizing with the Host Workstation Exploring the Terminal from the Workstation Explore The Mobile Device folder opens in Windows Explorer Adding Programs via ActiveSync Start Settings Control Panel If the File is Not an Installer ActiveSync Program Files If you want the program to persist through hard resets, save the program to the Autoinstall Honeywell Secure Wireless (SWC) Client User’s Guide www.honeywellaidc.com Adding Programs from the Internet 2.Select the program version that matches your Dolphin terminal and processor 4.Download the program to the terminal directly from the Internet Page Bluetooth Handler Scan Dialog 7.Highlight the Bluetooth printer device and tap the Select button 8.When the COM port selection appears, select COM7 and tap OK Registered Bluetooth Virtual COM ports 10.Tap OK to exit the Bluetooth Handler Dolphin HomeBase/eBase Device Front Panel Terminal Well Rubber Feet Back Panel USB Port Serial Port Ethernet Port (eBase only) Powering the Dolphin HomeBase Device eBase Clamp-onFerrite Core Installation Charging the Main Battery Inserting a Terminal Charging a Spare Battery Checking Battery Power Structural Dimensions Weight Material Color Page Dolphin 6100 ChargeBase Device (Model 6100-CB-1) Parts and Functions Only Connecting Power to the ChargeBase 1.Plug the A/C power cord into the power adapter 3.Plug the A/C power cord into a standard wall outlet 4.The base is ready to begin charging terminals Charging the Battery Mounting the ChargeBase Bottom Panel Desk Mounting Hardware Required Installing the DIN Rail Wall Mounting Hardware (Provided) Tools Required Hollow Wall Installation Wood Stud Installation Page Page Dolphin 6100 Net Base Device Power/DOCK LED This color means… COMM LED and status RJ45 Ethernet Ports Each Ethernet port has a dedicated green and yellow status LED For details on how to mount the Net Base, see Mounting the Net Base on page Connecting Power to the Net Base 5.The base is ready to begin charging terminals Applications on the Dolphin Terminal Displaying the Net Base Terminal Well and Dolphin IP Address Page Page Page Page Dolphin QuadCharger Device Charging Batteries Recommendations for Storing Batteries Troubleshooting Capacity Electrical Static Discharge Standard Capacity Extended Capacity Customer Support Limited Warranty Duration How to Extend Your Warranty Page Honeywell Scanning & Mobility