Honeywell T8611G installation instructions Installer Setup, Temperature Settings

T8611G CHRONOTHERM® IV DELUXE PROGRAMMABLE HEAT PUMP THERMOSTATS

Temperature Settings

Refer to Table 2 for the default program. If the daytime energy savings period is not used, press the period key (Leave or Return) until the time is blank. The fan setting feature is available on select thermostat models. See Owner’s Guide, form number 69-0940, for complete instructions on changing the program.

Table 2. Default Program Settings.

Period	Time	Heat	Cool	Fan
		Setpoint	Setpoint	Setting
Wake	6:45 AM	20°C	25°C	Auto
		(68°F)	(77°F)
Leave	8:45 AM	4.5°C	37°C	Auto
		(40°F)	(99°F)
Return	5:00 PM	20°C	25°C	Auto
		(68°F)	(77°F)
Sleep	10:00 PM	4.5°C	37°C	Auto
		(40°F)	(99°F)

—To change a setting, use the increase ! or decrease " key.

—To scroll the Installer Setup numbers backward, press the Time ∇ key.

—To exit the Installer Setup, press Run Program.

Wait	Set Program			Set Day/Time			Temporary		Setting	Em Heat
Recovery					AM
										Off
Hold for					PM					Cool
										Auto
Filter
		Em Ht	Aux Ht		Days
										Fan
Mon Tue Wed Thu Fri Sat Sun						Repl Batt Room			Outdoor
										On
Wake Leave			Return		Sleep	DST		Heat Cool		Auto

M14559

Fig. 9. Display of all LCD segments.

INSTALLER SETUP

NOTE: For most applications, the thermostat factory- settings will not need to be changed. Review the factory settings in Table 2 and if no changes are necessary, go to the Installer System Test section.

The Installer Setup is used to customize the thermostat to specific systems. Some of the options include temperature display, changeover and outdoor temperature display. Installer Setup numbers are listed in Table 3. The table includes all the configuration options and the factory-settings for the T8611.

A combination of key presses is required to use the Installer Setup feature:

—To enter the installer setup, press and hold the information i key with the increase ! and decrease " keys until the first number is displayed. All display segments appear for approximately three seconds before the number is displayed. See Fig. 9 and 10.

—To advance to the next Installer Setup, press the Time ∆ key.

INSTALLER SETUP	FACTORY SETTING OR OTHER
NUMBER DISPLAY	CHOICE DISPLAY (COLUMN 3
(COLUMN 2 OF TABLE 3)	OR 5 OF TABLE 3)
	M14618

Fig. 10. Display of Installer Setup

number and setting.

IMPORTANT

Only configurable numbers are shown on the device. Example: If thermostat does not have a system key, Installer Setup Number 12 will not be displayed. Review Table 3 factory-settings and mark any desired changes in the Actual Setting column. When Installer Setup is com- plete, review the settings to confirm that they match the system.

Table 3. Thermostat Installer Setup Options.

	Installer Setup	Factory Setting			Other Choices
	Number (Press			(Press ! or " key to change)
Select	Time ∆ key to					Actual
		Display	Description	Display	Description
	change)					Setting
Not Used.	1 thru 4	—	—	—	—	—
Heating cycle	5	6	Stage 2	1, 6 or 9	1—1 cph
rate.					6—6 cph used for last stage
					of heat pump systems
					9—9 cph used for electric
					heat
	6 (Not used)	—	—	—		—
	7	6	Emergency heat	3, 6 or 9
Not Used.	8 thru 11	—	—	—	—	—
System setting	12	1	Manual	0 or 2	0—Auto changeover
adjustment			changeover		2—Fixed auto changeover

69-1406—1 4