Hoover 56518114 D Lt, Do not use the deep cleaner on hard- wood floors, described, below, stairs

Models: 56518114

1 15
Download 15 pages 29.67 Kb
Page 11
Image 11
Do not use the deep cleaner on hard- wood floors.

4. Return d_;ep cleaner to upright posi-

tion, Lower handle and replace recovery tank.

5, Raise handle to upright position and

reposition clean solution tank,

To clean floor

Read "Before you begin cleaning" instructions on page 9.

Do not use the deep cleaner on hard- wood floors.

1, Fill clean solution tank with HOOVER

Barc-_ Floor

Cl{:aner

_ according

to

instructions for Figs, 2-8 to 2-14,

Do not use any type of wax with your

deep cleaner.

2.Move speed selector to the Lo or HI position for scrubbing or OFF if scrubbing is not desired.

3.Dry hands and plug deep cleaner

into a properly grounded outlet.

4.

Step

on

handle

 

release

pedal

and

lower

handle

to

operating

position;

turn

deep

cleaner

ON,

 

 

 

5.

To

release

solution,

press

trigger,

 

Slowly

move

d(;ep

cleaner

forward

and

backward

over

area

to be

cleaned,

 

6, To pick up dirty solution, release trig-

ger and slowly move deep cloaner ovc;r

area where solution has just been dis-

persed. Use both forward and reverse strokes,

7, Empty recovery tank when the motor

sound becomes higher pitched and

there is a loss in suction (see "Automatic

shut-off", Fig.2-6)

8, When finished cleaning, follow "After

cleaning '_instructions on pages 9-10.

Disconnect deep cleaner from electri-

cal outlet and remove attachment from

nozzle, Rinse i[ in clear water. Do not

remove plastic screen or foam from attachment.

*awlilabtE_

at additional

cost

if riot

includ-

ed

with

your

model

 

 

 

 

Your

model

includes

some

 

combination

 

Of

the

following

 

tools.

 

 

 

 

A. Powered hand tool has rotating

 

brushes

 

for

extra

scrubbing

 

[]ction

on

small

carpet

areas,

carpeted

 

stairs

and

upholstery,

For

some

models,

the

 

brushes

 

can

be

removed

for converting

to

the

scrub

module.

 

 

 

 

c

D

B. Stair/upholstery nozzle has a built-in

brush to help provide the scrubbing

action some spots may need for removal.

C. Scrub module with detachable

scrub pad* attaches to the base of the

powered hand tool (in place of brush

module), Can b[; used to scrub stubborn

areas such as scuff marks, dried spills,

and in hard to rr_-ach arc;as on hard sur- faces,

D. Crevice t0ol* can be used to clean

along edges of carpet, carpeted stairs and on upholstery.

_some models

:: , D "_LT_

Mow to attach tools

Disconnect deep cleaner from electri- cal outlet.

1. Place handle in upright position and

remove hose from rack,

All tools attach to the {hose in the same manner:

2. Connect tool to hose by sliding it onto

connector until the tab (C) locks it securely,

Using yOUr thumb, push forward and up

on the latch (D) to remow; tool as shown,

Before using tool

It may be necessary to remove air from

the system ("prime the pump") so the

clean solution wiil flow to the tool, Follow

these steps',

1 . Attach tool to hose and turn the de_'p

cleaner ON,

2. Put the tool on a hard surface or

against your hand to block off the suc- tion.

3. Walt a low seconds (carl tako up to 15

M

F

......

I

seconds). Then squeeze the trigger and

begin cleaning,

Follow

the

instructions

 

on

pages

12-13

for

the

appropriate

cleaning

ta._Jk.

Attaching

 

 

scrub

 

module*

 

1.

Open

 

the;

tool door

and

remove

the

powered

 

hand

tool.

 

 

 

 

2.

Grasp

 

the

sides

of

the

brush

module

and

lift

it

frorr_

the

base

(E),

 

3, Pull scrub module from deep cleaner

and snap it onto the base,

Note; It rnay be necessary to rotate the

scrub module (F)slightly so it will align

prop_'rly to the base,

Using the; scrub tool

With a little solution, test the scrub tool on a hidden area before using on

the desired surface. If no surface

change is visible, continue to use as

described

below.

 

 

 

 

 

1, Fill

clean

solution

 

tarlk

witb

HOOVER

Bare

Floor

Cleaner*

 

according

to

 

instructions

 

for Figs.

2-8 to 2-14.

 

2,

Hold

scrub

tool

 

above

area

to

be

cleaned

 

and

press

 

trigger

to

dispense

solution,

 

 

 

 

 

 

 

 

3,

Release

 

trigger

 

and scrub

area

with

tool,

 

Pick

 

up

dirty

solution

with

 

 

squeegee

 

as

shown.

 

 

 

 

 

*Included

 

with

some

 

models

 

 

 

Continued "_ 11

Page 11
Image 11
Hoover 56518114 D Lt, Do not use the deep cleaner on hard- wood floors, Do not use any type of wax with your, described