Horizon Fitness QUANTUM II Do not Stand on the Belt, Tensioning the Belt, O F I L E S P1 Manual

quantum II owner’s guidev1.1.qxd 8/14/2001 4:50 PM Page 12

DO NOT STAND ON THE BELT

While you are preparing to use the treadmill, do not stand on the belt. Place your feet on the side rails before starting the treadmill. Start walking on the belt only after the belt has begun to move. Never start the treadmill at a fast running speed and attempt to jump on!

TENSIONING THE BELT

If you can feel a slipping sensation when running on the treadmill, the running belt must be tightened. In most cases, the belt has stretched from use, causing the belt to slip. This is a normal and common adjustment. To eliminate this slipping, tension both the rear roller bolts with the 6MM Allen wrench, turning it 1/4 TURN to the right as shown. Try the treadmill again to check for slipping. Repeat if necessary, but NEVER TURN the roller bolts more than 1/4 turn at a time. The belt tension is set properly when the running belt is 1/4 of an inch from the deck.

P R O F I L E S

P1 - MANUAL

Customized workout, with no default Time.

P2 - INTERVALS

Speed changes; Time defaults to 24 minutes

Speed: 2.5, 3.0, 3.5, 6.0, 3.5, 6.0, 3.5, 6.0, 4.5, 3.5, 6.0, 3.5, 5.5, 3.5, 3.0, 2.5 (Mile) 4.0, 4.8, 5.6, 9.6, 5.6, 9.6, 5.6, 9.6, 7.2, 5.6, 9.6, 5.6, 8.8, 5.6, 4.8, 4.0 (KM)

P3 - ROLLING Speed changes; Time defaults to 48 minutes

Speed:

2.5, 3.0, 3.5, 4.0, 4.5, 5.0, 4.5, 4.0, 4.0, 4.5, 5.0, 4.5, 4.0, 3.5, 3.0, 2.5 (Mile) 4.0, 4.8, 5.6, 6.4, 7.2, 8.0, 7.2, 6.4, 6.4, 7.2, 8.0, 7.2, 6.4, 5.6, 4.8, 4.0 (KM)

P4 - WEIGHT LOSS

Elevation changes; Time defaults to 48 minutes

Elevation: 0, 1, 1, 2, 2, 3, 3, 4, 4, 5, 5, 4, 3, 2, 1, 0

Changing the Speed or Elevation

When in a program, the user is able to change the difficulty of the program by pressing the plus (+) or minus (-) buttons to the desired level. Note: The user is only able to increase or decrease the elevation or speed during the program. When in a program, if the user increases or decreases the difficulty of speed or elevation, all of the remaining program speeds or elevation segments will be modified as well. For example, when in P2, the first segment default speed is

2.5mph. If this speed is increased by 1 mph, all of the remaining segments will be increased by 1mph as well.

Quick Speed Keys

When in a program, the user is able to press any of the desired quick speed keys to get to a specific speed more quickly. Note: When in a speed-based program, if the user presses any of the quick speed keys, all of the remaining speed segments in the program will be modified as well. For example, when in P2, the first segment default speed is 2.5 mph. If the user presses the 4 mph quick speed key, all of the remaining segments will increase by 1.5 mph as well.

18 quantum II quantum II 11