INTRODUCTION IMPORTANT PRECAUTIONS
ASSEMBLY STEP 5
HARDWARE BAG 5 CONTENTS:
BOLT (G) | FLAT WASHER (B) | SPRING WASHER (C) |
16 mm | 8 mm | 8 mm |
Qty: 4 | Qty: 4 | Qty: 4 |
ASSEMBLY STEP 6
HARDWARE BAG 6 CONTENTS:
BOLT (A) | FLAT WASHER (B) | SPRING WASHER (C) |
|
|
| ARC WASHER (D) |
|
| |||||
20 mm | 8 mm | 8 mm |
|
|
| 8 mm |
Qty: 6 | Qty: 4 | Qty: 6 |
|
|
| Qty: 2 |
|
| |||||
|
|
|
|
|
|
|
IMPORTANT PRECAUTIONS INTRODUCTION
ASSEMBLY
BEFORE
YOU BEGIN
TREADMILL CONDITIONING TROUBLESHOOTING LIMITED
OPERATION GUIDELINES & MAINTENANCE WARRANTY
12
HANDLEBAR BRACKET |
CONSOLE |
FLAT WASHERS (B) |
SPRING WASHERS (C) |
BOLTS (G) |
LEFT SIDE: |
CONNECT PULSE |
CABLES ONLY |
RIGHT SIDE: |
CONNECT CONSOLE |
CABLES, PULSE CABLES |
AND POWER CABLES |
AOpen HARDWARE BAG 5.
BPlace CONSOLE onto HANDLEBAR BRACKETS as shown.
Note: Do not pinch CONSOLE CABLE when placing the console onto the handlebar brackets.
CInsert 2 Bolts (G), 2 SPRING WASHERS (C) and 2 FLAT washers
(B) through the bottom of the HANDLEBAR BRACKET to secure the console to the HANDLEBAR BRACKET.
DRepeat on other side.
EReach inside the right underside of the console to pull out the console cable, pulse cable and power cable. Attach to the matching cables that are hanging out of the cable hole in the handlebar.
FRepeat on left side to attach pulse cable.
GThread attached cables back through the cable holes when finished.
Note: Do not completely tighten any bolts until step 6 is complete!
| A | Open HARDWARE BAG 6. | |
| B With the running deck in the | ||
|
| lowered position, place the | |
|
| SUPPORT BAR between the | |
|
| HANDLEBAR and the main | |
|
| frame. | |
| C To attach the support bar, | ||
|
| insert 1 Bolt (A), 1 SPRING | |
ARC WASHER (D) |
| WASHER (C) and 1 ARC | |
| washer (D) in the top of the | ||
SPRING WASHER (C) |
| ||
HANDLEBAR | support bar and 2 Bolts | ||
| |||
BOLT (A) |
| ||
| (A), 2 SPRING WASHERS (C) | ||
|
| ||
|
| and 2 FLAT washers (B) in | |
SUPPORT BAR |
| the bottom of the support | |
|
| bar as shown. | |
BOLTS (A) | D | Repeat on the other side | |
SPRING WASHERS (C) | E | Connect power plug to the | |
FLAT WASHERS (B) | |||
|
| treadmill and connect the | |
|
| cord to a power outlet. The | |
MAIN FRAME |
| on/off switch is located next | |
|
| ||
|
| to the power cord. Flip this | |
| ON/OFF SWITCH | switch to the 'ON' position, so | |
| that the switch is lit. You will | ||
|
| ||
|
| hear a beep and the console | |
|
| will light up. | |
| F | Before the first use, lubricate | |
|
| the treadmill deck by | |
|
| following the instructions in | |
|
| the Maintenance section. | |
| CIRCUIT BREAKER |
| |
YOU’RE FINISHED!
13
ASSEMBLY
BEFORE YOU BEGIN
LIMITED TROUBLESHOOTING CONDITIONING TREADMILL WARRANTY & MAINTENANCE GUIDELINES OPERATION
T1201_Rev.1.7.indd | 7/31/08 4:52:44 PM |
