|
|
|
|
|
|
| INTRODUCTION |
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
| |
|
| IMPORTANT |
|
|
|
| PRECAUTIONS |
|
|
|
|
|
| |
|
| ASSEMBLY |
|
|
|
|
|
|
|
|
|
|
|
|
|
| YOU |
|
|
|
| BEFORE |
|
|
|
| BEGIN |
|
|
|
|
|
|
|
|
|
|
| |
|
| TREADMILL OPERATION |
|
|
|
|
|
|
|
|
|
|
| |
|
| CONDITIONING |
|
|
|
| GUIDELINES |
|
|
|
|
|
| |
|
| TROUBLESHOOTING |
|
|
|
| &MAINTENANCE |
|
|
|
|
|
| |
|
| WARRANTY |
|
|
|
| LIMITED |
|
|
| ||||
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
P R E-ASS E M B LY
Disassemble box and remove the cardboard packaging that is not beneath the treadmill. Do not attempt to lift the treadmill at this time. Remove plastic wrap from console masts.
*Note: During each assembly step, ensure that ALL nuts and bolts are in place and partially threaded in before completely tightening any ONE bolt. A light application of grease may aid in the installation of hardware. Any grease, such as lithium bike grease is recommended.
ASSEMBLY STEP 1
HARDWARE BAG 1 CONTENTS:
BOLT (A) | FLAT WASHER (B) | SPRING WASHER (C) |
|
|
| ARC WASHER (D) |
|
| |||||
20 mm | 8 mm | 8 mm |
|
|
| 8 mm |
Qty: 6 | Qty: 4 | Qty: 6 |
|
|
| Qty: 2 |
|
| |||||
|
|
|
|
|
|
|
|
| A | Open HARDWARE BAG 1. |
|
| B Slide LEFT CONSOLE MAST into MAIN | |
|
|
| FRAME BRACKET. |
|
| C Insert 2 Bolts (A), 2 SPRING WASHERS | |
|
|
| (C) and 2 FLAT washers (B) from the |
|
|
| bottom outside of the mast to secure |
| FLAT WASHERS (B) |
| the console mast to the main |
| SPRING WASHERS (C) |
| frame bracket. |
| BOLTS (A) | D | Insert 2 Bolts (A), 2 SPRING WASHERS |
|
| ||
LEFT CONSOLE MAST |
|
| (C) and 2 FLAT washers (B) from the |
|
|
| bottom inside of the mast to secure the |
ARC WASHERS (D) |
|
| console mast to the main frame |
SPRING WASHERS (C) |
|
| bracket. |
BOLTS (A) |
| E | Insert 2 Bolts (A), 2 SPRING WASHERS |
|
| ||
FLAT WASHERS (B) |
|
| (C) and 2 arc washers (D) from |
|
| the front of the mast to secure the | |
SPRING WASHERS (C) |
|
| |
|
| console mast to the main frame | |
BOLTS (A) |
|
| |
|
|
| bracket. |
| MAIN FRAME BRACKET |
|
|
|
|
| Note: Do not completely tighten |
|
|
| any screws or bolts until step 6 is |
|
|
| complete! |
ASSEMBLY STEP 2
HARDWARE BAG 2 CONTENTS:
BOLT (A) | FLAT WASHER (B) | SPRING WASHER (C) |
|
|
| ARC WASHER (D) |
|
| |||||
20 mm | 8 mm | 8 mm |
|
|
| 8 mm |
Qty: 6 | Qty: 4 | Qty: 6 |
|
|
| Qty: 2 |
|
| |||||
|
|
|
|
|
|
|
CONSOLE CABLE | RIGHT CONSOLE MAST | A | Pull LEAD WIRE through RIGHT | |
|
|
| CONSOLE MAST. | |
| LEAD WIRE |
|
| |
|
|
| After pulling the lead wire through | |
|
|
| the mast, the top of the console cable | |
|
|
| should be located at the top of the | |
|
|
| mast. Detach and discard lead wire. | |
|
| B Open HARDWARE BAG 2. | ||
|
| C Slide RIGHT CONSOLE MAST into MAIN | ||
|
|
| FRAME BRACKET. | |
|
|
| Note: Do not pinch CONSOLE CABLE | |
|
|
| when placing the mast onto the main | |
|
|
| frame. | |
|
| D | Insert 2 Bolts (A), 2 SPRING | |
|
|
| WASHERS (C) and 2 FLAT washers | |
|
|
| (B) from the bottom outside of the | |
|
|
| mast to secure the console mast to | |
RIGHT CONSOLE MAST | FLAT WASHERS (B) |
| the main frame bracket. | |
|
|
| ||
| SPRING WASHERS (C) | E | Insert 2 Bolts (A), 2 SPRING | |
ARC WASHERS (D) | BOLTS (A) | |||
| WASHERS (C) and 2 FLAT washers | |||
|
| |||
SPRING WASHERS (C) |
|
| ||
|
| (B) from the bottom inside of the mast | ||
BOLTS (A) |
|
| ||
|
| to secure the console mast to the | ||
|
|
| ||
|
|
| main frame bracket. | |
| CONSOLE CABLE | F | Insert 2 Bolts (A), 2 SPRING | |
|
|
| ||
| MAIN FRAME BRACKET |
| WASHERS (C) and 2 arc washers (D) | |
|
|
| ||
FLAT WASHERS (B) |
|
| from the front of the mast to secure | |
|
|
| ||
SPRING WASHERS (C) |
|
| the console mast to the main | |
BOLTS (A) |
|
| ||
|
| frame bracket. | ||
|
|
| ||
|
|
| Note: Do not completely tighten | |
|
|
| any screws or bolts until step 6 is | |
|
|
| complete! | |
IMPORTANT PRECAUTIONS INTRODUCTION
ASSEMBLY
BEFORE YOU BEGIN
LIMITED TROUBLESHOOTING CONDITIONING TREADMILL WARRANTY & MAINTENANCE GUIDELINES OPERATION
T1201_Rev.1.7.indd | 7/31/08 4:52:34 PM |
