CONNECTING HDMI COMPONENTS
HDMI JACK
This unit has 3 HDMI inputs and one HDMI output. It can send digital video and audio signals from DVDs and other sources directly to a display. It minimizes signal degradation caused by analog conversion so that high quality images can be enjoyed.
Select an input source from the OSD menu system. (See page 27)
Notes:
•When the HDMI output is connected to a display monitor that does not support HDCP*, signals are not output. To view images in HDMI, it is necessary to connect to a display that supports HDCP*.
•There may be no image output if connected to a TV or display that is not compatible with the above format.
•Refer to the instruction manual of the TV or display to be connected to the unit for detailed information regarding the HDMI terminal.
*HDCP:
CONNECTING HDMI COMPONENTS
An HDMI cable (sold separately) is used to connect the HDMI jack on the unit with the HDMI jack on a DVD player, TV, projector or other component. To transmit multichannel audio via HDMI, the connected player must support multichannel audio transmission through its HDMI jack.
HDMI video streaming is compatible with DVI in principle. Therefore, it is possible to connect to a TV or monitor that has a DVI terminal using an
Notes:
•Some HDMI components can be controlled over the HDMI cable, but this unit cannot control other components this way.
•When connected to a monitor (i.e., TV, projector, etc.) that does not support HDCP, video and audio are not output.
•DVI cables come with
•Some source devices such as DVD players does not support HDMI repeater like those of the unit. In such case, pictures are not properly projected on monitors such as TVs and projectors.
•When multiple components are connected to this unit, turn power to unused components off to prevent interference between them.
•Disconnecting or connecting cables with the power on can damage the equipment. Turn the power off before disconnecting or connecting cables.
•Some
•If a DVD player that does not support HDMI 1.1 is connected to the unit, multi channel PCM playback is not possible even with
•If a DVD player or other device with DVI output is connected to the unit, a separate audio cable (optical- digital, coaxial digital or analog) is needed for the audio signals. In this case, select the connected audio input as explained in “1 INPUT SETUP”. (See page 27)
•Multi channel PCM signals and audio signals of 64 kHz or higher that are input from the HDMI jack are not output from the DIGITAL OUT jacks.
•Depending on the quiality of the cable used, the HDMI signal may be affected by noise.
•Audio units that use sampling frequencies of 128 kHz and above are not supported.
•When only HDMI components are connected, OSD will not be displayed. (See page 26)
DVD player | VIDEO PROJECTOR | ENGLISH |
HDMI OUTPUT | HDMI INPUT | |
|
|
|
|
| INPUT |
|
|
|
|
| COMPONENT |
|
|
| HDMI Ver 1.1 | |||
|
|
| 1 |
|
|
|
| INPUT |
|
|
| |||||
|
|
|
|
|
|
|
| 3 | VIDEO |
|
|
|
|
|
| |
|
|
|
|
|
| 1 |
|
|
| MONITOR |
|
|
|
| ||
|
|
|
|
|
|
|
|
| OUT 2 |
|
|
|
|
| ||
|
|
| INPUT |
|
|
|
|
|
|
| INPUT 1 | INPUT 2 | INPUT 3 | OUTPUT | ||
CR IN VCR OUT | DSS | MONITOR OUT 2 Y | CB/PB | CR/PR | Y | CB/PB CR/PR | Y | CB/PB | CR/PR | |||||||
|
|
|
|
| ||||||||||||
|
|
|
|
|
|
|
|
|
| IN |
|
|
| XM |
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
| 4 | 5 |
|
|
|
|
|
|
|
| |
|
|
|
|
|
| 1 | 2 | 3 |
|
|
|
|
|
|
| |
IN | OUT |
| IN | OUT | IN | OUT |
|
| OPT | OUT | FLASHER | DC |
|
|
| |
| VCR | DSS | TAPE | CD/CDR | DIGITAL IN |
| DIGITAL OUT REMOTE CONT. | IN | TRIGGER |
|
|
| ||||
|
|
| AUDIO |
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
| AC IN |
|
|
| |
| R | L | R | L | R | L |
|
|
|
|
|
|
|
|
| |
R. | FRONT A | SURROUND BACK | SURROUND | CENTER |
|
| SWITCHED |
|
|
|
|
| ||||
|
| SPEAKER C/MULTI SPEAKER |
|
| SPEAKER |
|
| 1.25A 150W |
| MODEL NO. SR5002 |
|
| ||||
MS |
| SURR.SURR BACK : |
| SYSTEMS |
|
| AC OUTLETS |
|
| |||||||
|
|
|
|
|
|
|
| |||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||
120V
60Hz
Satellite Tuner
HDMI OUTPUT
21
