Marantz SR4002/SR5002 Recalling a Preset Station, Preset Scan, Clearing Stored Preset Stations

(Using the remote controller)

1. Tune into the radio station you desire (Refer to the “MANUAL TUNING” or “AUTO TUNING” section).

2. Press the MEMO button on the remote controller. “– –“ (preset number) starts blinking on the display.

3. Enter the desired preset number by pressing the numeric buttons.

Note:

When entering a single digit number (2 for example), either input “02” or just input “2” and wait for a few seconds.

RECALLING A PRESET STATION

1.	SLEEP	DISPLAY	P.DIRECT	SURROUND
				LIP SYNC/
	AUTO		dts	INPUT
1.	1	2	3
	CS	EX/ES	VIRTUAL	T.MODE
	4	5	6
	M-CH ST	STEREO	NIGHT	P.SCAN
	7	8	9
		7.1CH IN	A/D	HT-EQ
	CL	0	+10	MEMO
	CH/ CAT	SPKR A/B	MUTE	VOLUME
	REC	T.DISP	PTY	F.DIRECT
1.	- PRESET +		- TUNING +
	DISC+	ANGLE	SUB TITLE	AUDIO

(Using the unit)

1. Select the desired preset station by pressing the 1 or 2 cursor buttons on the front panel

(Using the remote controller)

1. Press the S or T buttons to select the desired preset station, or input your desired preset channel with the numeric buttons on the remote controller.

PRESET SCAN

	CS	EX/ES	VIRTUAL	T.MODE	1.
	7	8	9
	4	5	6
	M-CH ST	STEREO	NIGHT	P.SCAN
3.		7.1CH IN	A/D	HT-EQ	3.
	CL	0	+10	MEMO
	CH/ CAT	SPKR A/B	MUTE	VOLUME
	REC	T.DISP	PTY	F.DIRECT
	- PRESET +		- TUNING +		3.
	DISC+	ANGLE	SUB TITLE	AUDIO
	CH-SEL	V-OFF	ATT.

(Using the remote controller)

1. Press the P.SCAN on the remote controller.

“PRESET SCAN” appears on the display and then the preset station with the lowest preset number is recalled first.

2. Preset stations are recalled in sequence (No.1

→No.2 → etc.) for 5 seconds each.

No stored preset number will be skipped.

3. You can fast forward the preset stations by pressing the T continuously.

When the desired preset station is received, cancel the preset scan operation by pressing the CLEAR button or P.SCAN on the remote controller.

CLEARING STORED PRESET STATIONS

You can remove preset stations from the memory using the following procedure.

2.	3.	1	2	3	LIP SYNC/
		AUTO		dts	INPUT
	2.	CS	EX/ES	VIRTUAL	T.MODE
		7	8	9
		4	5	6
		M-CH ST	STEREO	NIGHT	P.SCAN
			7.1CH IN	A/D	HT-EQ
		CL	0	+10	MEMO
	3.	CH/ CAT	SPKR A/B	MUTE	VOLUME
			MULTI/ CAT	M-SPKR
		INFO			MENU

1. Recall the preset number to be cleared with the method described in “Recalling” a preset station.

2. Press the MEMORY button on the front panel or press the MEMO button on the remote controller.

3. The stored preset number blinks in the display for 5 seconds. While blinking, press the CLEAR button on the front panel or the remote controller.

4. “xx CLEAR” appears on the display to indicate that the specified preset number has been cleared.

Note:

To clear all stored preset stations, press and hold the CLEAR and the ENTER buttons for two seconds.

SORTING PRESET STATIONS

AV SURROUND RECEIVER SR5002

If you have stations memorized, and there is a gap in the sequential order:

I.e. the stations are stored as follows

1)87.1 MHz

2)93.1 MHz

3)94.7 MHz

10)105.9 MHz

(notice there is no stations programmed for pre sets for 4-9), you can have pre set 10 become pre set 5: To sort the numbers, press the 4cursor button while pressing the MEMORY button.

“PRESET SORT” will appear on the display and sorting will be done.

NAME INPUT OF THE PRESET STATION.

This function allows the name of each preset channel to be entered using alphanumeric characters. Before name inputting, you need to store preset stations with the preset memory operation.

4. 5. 2. 5. 6.

AV SURROUND RECEIVER SR5002

2. 5. 6.	7	8	9
		7.1CH IN	A/D	HT-EQ
	CL	0	+10	MEMO
	CH/ CAT SPKR A/B		MUTE	VOLUME
		MULTI/ CAT	M-SPKR
	INFO			MENU
		ENTER
	T.TONE
	/SET UP			EXIT
	REC	T.DISP	PTY	F.DIRECT
5.	- PRESET +		- TUNING +
	DISC+	ANGLE	SUB TITLE	AUDIO
4.	CH-SEL V-OFF		ATT.
		BASS	TREBLE
	TV	DVD	VCR	DSS

1. Recall the preset number to be inputted name with the method described in “Recalling” a preset station.

2. Press the MEMORY button on the front panel or press the MEMO button on the remote controller for more than 3 seconds.

3. The left most column of the station name indicator flashes, indicating the character entry ready status.

4. When you press the 3 or 4 cursor buttons on the front panel or the 5 / 6 buttons on the remote controller, alphabetic and numeric characters will be displayed in the following order:

A → B → C ... Z → 1 → 2 → 3 ..... 0 → – → +

→/ → (Blank) → A UP →

←DOWN

5.After selecting the first character to be entered, press the MEMORY or ENTER buttons, press the MEMO button on the remote controller.

The entry in this column is fixed and the next column starts to flash. Fill the next column the same way.

To move back and forth between the characters, press the 1 / 2 cursor buttons or press S or T buttons on the remote controller.

Note:

Unused columns should be filled by entering blanks.

6. To save the name, press the MEMORY button on the front panel or remote controller for more than 2 seconds.

Ten keypad	Press, press again, press again, etc.
1	A → B → C → 1 → A
2	D → E → F → 2 → D
3	G → H → I → 3 → G
4	J → K → L → 4 → J
5	M → N → O → 5 → M
6	P → Q → R → 6 → P
7	S → T → U → 7 → S
8	V → W → X → 8 → V
9	Y → Z → space → 9 → Y
0	– → + → / → 0

ENGLISH

43