Marantz SR4002/SR5002 manual Tuner, Basic Operation, English, Auto Tuning, Manual Tuning

ENGLISH

BASIC OPERATION

(TUNER)

LISTENING TO THE TUNER

Frequency scan step for AM is selectable.

Default setup is 10 kHz step, if your country’s standard is 9 kHz step, press BAND button on the remote controller more than 6 seconds. Scan step will change.

Note:

Preset memory for the tuner will clear by changing this setup.

AUTO TUNING

2.	1.	SLEEP	DISPLAY	P.DIRECT	SURROUND
		1	2	3	LIP SYNC/
		AUTO		dts	INPUT
	1.				BAND
		CS	EX/ES	VIRTUAL	T.MODE
		4	5	6
		M-CH ST	STEREO	NIGHT	P.SCAN

7 8 9

REC T.DISP PTY F.DIRECT

2. - PRESET + - TUNING +

DISC+ ANGLE SUB TITLE AUDIO

MANUAL TUNING

2.	1.	SLEEP	DISPLAY	P.DIRECT	SURROUND
					LIP SYNC/
		AUTO	2	dts	INPUT
	1.	1		3	BAND
		CS	EX/ES	VIRTUAL	T.MODE
		4	5	6
		M-CH ST	STEREO	NIGHT	P.SCAN

7 8 9

REC T.DISP PTY F.DIRECT

2. - PRESET + - TUNING +

DISC+ ANGLE	SUB TITLE AUDIO
CH-SEL V-OFF	ATT.
BASS	TREBLE

(Using the unit)

1. To select tuner and desired band (FM or AM), press the BAND button on the front panel.

2. Press the 3 or 4 cursor buttons on the front panel to select the desired station.

(Using the remote controller )

1. To select tuner and desired band (FM or AM), press the BAND button on the remote controller.

2. Press the 5 or 6 on the remote controller to tune in the desired station.

(FM) TUNING MODE (AUTO STEREO OR MONO)

SOURCE	SET	OFF	ON
l/
SLEEP	DISPLAY	P.DIRECT	SURROUND
			LIP SYNC/
AUTO		dts	INPUT
1	2	3
CS	EX/ES	VIRTUAL	T.MODE
4	5	6
M-CH ST	STEREO	NIGHT	P.SCAN
7	8	9
	7.1CH IN	A/D	HT-EQ
CL	0	+10	MEMO
CH/ CAT	SPKR A/B	MUTE	VOLUME

When in the auto stereo mode, AUTO indicator will be illuminated on the display.

The “ST” indicator is illuminated when a stereo broadcast is tuned in.

At open frequencies, the noise is muted and the “TUNED” and “ST” indicators are not illuminated.

If the signal is weak, it may be difficult to tune into the station in stereo. In such a case, press the T-MODEbutton on the front panel or remote controller.

“AUTO” indicator is not illuminated, if FM stereo broadcasts are received in monaural and the “ST” indicator is not illuminated.

To return to auto stereo mode, press the T-MODEbutton or press T-MODEbutton on the remote controller again. AUTO indicator is illuminated on the display.

2. While pressing the MEMO button, press the 2 cursor button.

“AUTO PRESET” will appear on the display, and scanning starts from the lowest frequency.

3. Each time the tuner finds a station, scanning will pause and the station will be played for five seconds.

During this time, the following operations are possible.

The band can be changed by the BAND button.

4. If no button is pressed during this period, the current station is memorized in location Preset 02.

If you wish to skip the current station, press the 3 cursor button during this period, this station is skipped and auto presetting continues.

5. Operation stops automatically when all 50 preset memory positions are fi lled or when auto scanning attains the highest end of all bands. If you desire to stop the auto preset memory at anytime, press the CLEAR button.

Note:

It is possible that existing preset memory positions will be overwritten.

CH-SEL V-OFF ATT.

(Using the unit)

1. To select tuner and desired band (FM or AM), press the BAND button on the front panel.

2. Press the 3 or 4 cursor buttons on the front panel for more than 1 second to start the auto tuning function.

3. Automatic searching begins then stops when a station is tuned in.

(Using the remote controller)

1. To select tuner and desired band (FM or AM), press the BAND button on the remote controller.

2. Press the 5 or 6 for more than 1 second on the remote controller.

3. Automatic searching begins then stops when a station is tuned in.

If tuning does not stop at the desired station, use to the “Manual tuning” operation.

DIRECT FREQUENCY CALL

						SLEEP	DISPLAY	P.DIRECT	SURROUND
	SOURCE	SET	OFF	ON
	l/					AUTO		dts	LIP SYNC/
									INPUT
	SLEEP	DISPLAY	P.DIRECT	SURROUND	1.	1	2	3	BAND
				LIP SYNC/		CS	EX/ES	VIRTUAL	T.MODE
	AUTO		dts	INPUT		4	5	6
	1	2	3
3.						M-CH ST	STEREO	NIGHT	P.SCAN
	CS	EX/ES	VIRTUAL	T.MODE		7	8	9
	4	5	6
	M-CH ST	STEREO	NIGHT	P.SCAN			7.1CH IN	A/D	HT-EQ
	7	8	9
		7.1CH IN	A/D	HT-EQ		/SET UP			EXIT

CL 0 +10 MEMO

CH/ CAT	VOLUME	2.	REC		T.DISP	PTY	F.DIRECT
SPKR A/B	MUTE
MULTI/ CAT	M-SPKR		-	PRESET +		- TUNING +

1. To select tuner and desired band (FM or AM), press the BAND button on the remote controller.

2. Press the F.DIRECT on the remote controller, display will show “FREQ - - - -”.

3. Input your desired station’s frequency with the numeric buttons on the remote controller.

4. The desired station will automatically be tuned.

PRESET MEMORY

With this unit you can preset up to 50 FM/AM stations in any order.

For each station, you can memorize the frequency and reception mode if desired.

AUTO PRESET MEMORY

This function automatically scans the FM and AM band and enters all stations with proper signal strength into the memory.

2. 4. 2. 5. 1. 3.

AV SURROUND RECEIVER SR5002

1. To select FM, press the BAND button on the front panel.

MANUAL PRESET MEMORY

3.	2. 4.	SLEEP	DISPLAY	P.DIRECT	SURROUND
					LIP SYNC/
		AUTO		dts	INPUT
CEIVER SR5002	3.	1	2	3
		CS	EX/ES	VIRTUAL	T.MODE
		4	5	6
		M-CH ST	STEREO	NIGHT	P.SCAN
		7	8	9
			7.1CH IN	A/D	HT-EQ
	2.	CL	0	+10	MEMO
		CH/ CAT	SPKR A/B	MUTE	VOLUME
			MULTI/ CAT	M-SPKR
		INFO			MENU

(Using the unit)

1. Tune into the radio station you desire (Refer to the “MANUAL TUNING” or “AUTO TUNING” section).

2. Press the MEMORY button on the front panel. “– –“ (preset number) starts blinking on the display.

3. Select the preset number by pressing the 1 or 2 cursor buttons, while this is still blinking (approx. 5 seconds)

4. Press the MEMORY button again to enter. The display stops blinking.

The station is now stored in the specified preset memory location.

42