D ISHWASHER
How to use your Dishwasher
First of all.
-Turn on the water supply tap completely.
-Add the correct amount of detergent.
-Load the baskets cor- rectly.
-Check that the spray arms rotate freely.
-Close the door securely.
-Press the
Select the wash cycle. Turn knob "M" until the reference notchontheknobcorrespondswith the number or symbol for the cycle you wish to set (see programme chart). Press the Start button "R" and the wash cycle starts up, the approximateamountoftimeleftuntil the end of the wash cycle is displayed.Afterafewseconds,you will hear a short beep: the wash cycle has begun and indicator "G" displays the symbol corresponding to the cycle starting phase.The counter "L" will indicate the estimated amount of time left until the end of the wash cycle
Indicator lights.
Your dishwasher is provided with an indicator light "G" with 4 sym- bols which come on as the appli- ance carries out each phase of the selected programme.
These indicator lights represent each phase corresponding to:
Modifying a wash cycle in progress.
But if you have chosen the wrong cycle, not to worry! You can modify the wash cycle in progress only if it has only just started.
KeeptheResetbutton "R"pressed for about 3 seconds:
a prolonged beep will sound, followed by three short beeps. The cancelled cycle time will flash on the display. Turn the knob to select a new wash cycle.
You've left out a dish? Interrupt the wash cycle by press- ing the
The cycle will start up from where you interrupted it.
Cycle end
The end of the wash cycle is indicated by two short beeps and the word "END" flashes on the display.
Warning!
Turn the appliance off by pressingbutton“A”,unplugthe appliance from the electricity socket to cut off the power supply;thepowersupplycable should consequently be easily accessible.
Turn off the water tap.
Wait a few minutes before unload- ing the dishes: they are very hot! If youwaitalittlewhile,theydrybetter due to the steam.
Make sure the wash cycle has endedbeforeremovingthedishes!
Empty the lower basket first.
There's been a power failure or you opened the dishwasher door
The wash cycle stops and then restarts when the electricity comes backonorwhenyouclosethedoor.
You decide when it starts.
When you have loaded the dishes, you can choose when to start your dishwasherbeforesettingthewash cycle desired.
Press button "I" repeatedly to postponethestartofthewashcycle from 01 hour to 24h.
If you press the button again, the word "OFF" is displayed (no selection made).
Once you have made your selection, make sure the appliance doorisshutandstartthewashcycle by pressing the START button.
Symbol "U" lights up on the display and the countdown begins.
Oncethecountdownisup,thewash cycle begins and the approximate amount of time left until the end of the wash cycle is displayed. A quick look at the indicator lights will keepyouinformedofthecountdown progress at all times.
Have you changed your mind?
If you change your mind, you can set a shorter time delay: press button "I" to select it. You need not reset the wash cycle.
Ifyouhavechangedyourmindand wish to start the wash cycle immediately, press button "I" until the countdown is fully reset. Indicator light "U" will turn off and the cycle will start at the sound of a beep.
The indicator light corresponding to the cycle phase under way will come up on the display and the countdown to the estimated cycle endbegins.
Half load.
Your dishwasher also allows you to wash half a load When you only have little cutlery to wash, you can run just half a load on the upper rack, saving on both water and electricity.
Press button "N"; you will hear a beep and the symbol ‘V’ corresponding to the half load will
light up.
Once you have made your setting, start the wash cycle by pressing the START button.
-This option is available with all wash cycles.. Press it once more to reset the rack selection and the dishwasherwillconsequentlywash on both racks.
How to programme “extra” drying
If you want your dishes to be perfectly dry, follow the instructions below.
Press button "H". After a prolonged beep, indicator light "Z" lights up and the time corresponding to the wash cycle selected on the knob will flash on the display.
To disable the extra drying option, pressthesamebuttonandindicator light "Z" will be turned off after a beep is sounded.
This option is incompatible with the soak cycle. Remember that with extra drying, the wash cycle will last longer, to provide you with drier dishes.
7
