Troubleshooting

Your Washer-dryer could fail to work. Before contacting the Technical Assistance Centre (see “Assistance”), make sure

 

GB

that the problem cannot be not solved easily using the following list.

 

 

 

Problem:

The machine does not switch on.

The wash cycle does not start.

The machine does not dry.

The clothes are too hot when the drying cycle is finished.

The machine does not fill with water or the indicator light for the first wash cycle stage flashes rapidly.

Possible causes / Solutions:

•The appliance is not plugged into the socket fully, or not enough to make contact.

•There is no power to the socket, or the fuse has blown in the mains plug.

•The door is not closed properly.

•The ON/OFF button has not been pressed.

•The START/PAUSE button has not been pressed.

•The water tap has not been turned on to allow water to flow into the machine.

•A delayed start has been set.

•Check the 2 sections above.

•The ‘DRYING’ selector knob has in the position.

•A cooling-down period is always added to the end of each drying cycle. If the clothes appear too hot to handle leave the door open to allow to cool further before removing from the machine.

•The water inlet hose is kinked.

•The water inlet hose is not connected to the water supply.

•The water pressure is too low.

•The water tap has not been turned on to allow water to flow into the machine.

•There is no water supply to the house.

•The inlet valve filter is blocked.

•The START/PAUSE button has not been pressed.

The machine continuously fills with wa- ter and continually drains away

or Water left in the drum or Stuck on wash.

•The top of the drain hose is too low - It must be fitted at a height between

65 and 100 cm from the floor (see “Installation”).

•The drain hose is connected incorrectly to the sink trap allowing water to run into the machine, the drain hose must be positioned higher than the bottom of the sink to prevent water flowing down the drain hose.

•The end of the drain hose has been pushed too far down the standpipe, the ‘U’ bracket should be fitted 100 mm from the end of the drain hose.

The machine does not drain or spin (error lights flashing).

•The Pump filter is blocked.

•The drain hose is kinked (see “Installation”).

•New Installation - The blanking cap or spigot has not been removed if connected under a sink.

•The drain hose or sink trap is blocked.

The wash programme takes too long.

•Programme times will vary due to water pressure, the incoming water temperature and if the wash load goes out of balance. This will increase the programme times accordingly (see ‘ The machine wont spin properly’ below) - (Most Common Cause!).

The machine vibrates a lot during the spin cycle.

•The feet have not been adjusted, enabling the machine to rock.

•New Installation - Either the Transit Bolts including the plastic spacers, or the Polystyrene Packaging have not been removed when installing the machine.

•The machine is trapped between cabinets and/or walls.

•The load is in a slight out of balance condition and machine is spinning, but at a lower speed.

The machine is noisy.

• There will always be some motor, pump and drum noise during spin.

15

Page 14 Page 16
Page 15
Image 15
Hotpoint BHWD 129 manual Troubleshooting, Problem, Possible causes / Solutions
Page 14 Page 16

BHWD 129 specifications

The Hotpoint BHWD 129 is a versatile and efficient washer-dryer combo designed to meet the needs of modern households. With its sleek design and array of advanced features, this appliance stands out as a practical solution for individuals and families looking to save space without compromising on performance.

One of the key features of the Hotpoint BHWD 129 is its generous load capacity. This model can handle up to 6 kg of laundry in the washing cycle and 5 kg in the drying cycle, making it suitable for small to medium-sized households. The combination of washing and drying in one unit allows users to streamline their laundry routine, saving time and effort.

In terms of technology, the Hotpoint BHWD 129 is equipped with an Eco cycle, which optimizes water and energy usage, making it an environmentally friendly choice. The machine also features a range of wash programs tailored to different fabric types and laundry needs. From quick washes for those in a hurry to more intensive cycles for heavily soiled items, the machine offers flexibility to cater to various laundry requirements.

Another notable characteristic of the Hotpoint BHWD 129 is its Spin Cycle performance. With a maximum spin speed of 1200 RPM, it effectively removes excess water from clothing, reducing drying times significantly. This feature is particularly advantageous for those using the drying function, as it allows laundry to dry more quickly and efficiently.

The appliance also includes a range of temperature settings, enabling users to customize the washing process according to the specific needs of their fabrics. The intuitive control panel ensures that selecting the right program is straightforward, making it user-friendly for individuals of all skill levels.

In addition, the Hotpoint BHWD 129 incorporates advanced noise reduction technology, allowing for quieter operation. This makes it a suitable choice for apartments or homes where noise levels should be kept to a minimum. The design also ensures that maintenance is easy, allowing users to keep the machine in top condition with minimal effort.

Overall, the Hotpoint BHWD 129 is an excellent choice for those seeking a compact, efficient, and multifunctional washer-dryer combo. Its combination of advanced features, user-friendly design, and eco-conscious technology makes it a valuable addition to any laundry room. Whether you have a busy family or are living single, this machine offers the reliability and performance necessary to make laundry day a breeze.
Top Page Image Contents