connection required and position the connection GB supports as shown in the following table and

diagrams.

4. Position the wires in accordance with the information given in the following table and diagrams and connect the appliance by tightening all the screws for the springs as much as possible.

Voltage and

Electrical connections

Terminal board

mains frequency

 

 

400V 3-N ~

 

Three-phase 400

50/60 Hz

 

 

 

 

 

 

5. Secure the power supply cable by fastening the cable clamp screw, then put the cover back on.

Phase

Phase

Phase

 

1

2

3

Three-phase 400

 

5

4

 

Earth Neutral

U-bolt

 

 

connection support

Connecting the electricity supply cable to the mains

If the appliance is being connected directly to the electricity mains an omnipolar switch must be installed with a minimum opening of 3 mm between contacts.

￿The installer must ensure that the correct electrical connection has been made and that it is fully compliant with safety regulations.

Before connecting the appliance to the power supply, make sure that:

•The appliance is earthed and the plug is compliant with the law.

•The socket can withstand the maximum power of the appliance, which is indicated on the data plate located on the appliance itself.

•The voltage falls within the range of values indicated on the data plate.

•The socket is compatible with the plug of the appliance. If the socket is incompatible with the plug, ask an authorised technician to replace it. Do not use extension cords or multiple sockets.

￿Once the appliance has been installed, the power supply cable and the electrical socket must be easily accessible.

￿The cable must not be bent or compressed.

￿The cable must be checked regularly and replaced by authorised technicians only.

￿The manufacturer declines any liability should these safety measures not be observed.

￿Do not remove or replace the power supply cable for any reason. Its removal or replacement will void the warranty and the CE marking. INDESIT does not assume liability for accidents or damage arising from replacement/removal of the original power supply cable. Replacement can only be accepted when carried out by personnel authorised by INDESIT and using an original spare part.

4

Page 3 Page 5
Page 4
Image 4
Hotpoint CRA 641 DC operating instructions Three-phase
Page 3 Page 5

CRA 641 DC specifications

The Hotpoint CRA 641 DC is an innovative and efficient cooking appliance that combines modern technology with user-friendly features for an exceptional culinary experience. Known for its sleek design and practical functions, this built-in gas cooktop is ideally suited for contemporary kitchens, making it an excellent choice for home chefs and cooking enthusiasts alike.

One of the standout features of the Hotpoint CRA 641 DC is its four high-efficiency burners. These burners provide varying levels of heat output, allowing for complete versatility when preparing meals. The powerful burners cater to different cooking techniques, from simmering sauces at low heat to boiling water or searing meat at high temperatures. This flexibility is crucial for multitasking in the kitchen, enabling users to manage different dishes simultaneously.

The cooktop's surface is crafted from durable stainless steel, which ensures longevity and ease of maintenance. Its smooth finish not only enhances the aesthetic appeal of the kitchen but also makes cleaning a hassle-free task. The surface is designed to resist stains and scratches, keeping the appliance looking new over time.

Safety is a priority in the design of the Hotpoint CRA 641 DC. It features a flame failure device that automatically shuts off the gas supply in case the flame goes out. This essential safety feature provides peace of mind while cooking, as users can focus on their culinary creations without worrying about potential hazards.

Another significant aspect of the Hotpoint CRA 641 DC is its ergonomic control knobs, which are designed for easy operation. The front-mounted knobs allow for straightforward access and control, ensuring that users can adjust the flame levels with precision.

Moreover, this cooktop is compatible with various cookware types, including cast iron, stainless steel, and non-stick materials. The versatility of the cooktop ensures that users can utilize their preferred pots and pans without limitation.

Overall, the Hotpoint CRA 641 DC is an excellent addition to any culinary space, marrying style, functionality, and safety. Its smart features and user-oriented design offer a seamless cooking experience that caters to both novice cooks and seasoned chefs, making it a noteworthy consideration for anyone looking to enhance their kitchen capabilities. The combination of advanced technology and considerate design embodies what modern cooking appliances should be. Whether preparing simple weeknight meals or hosting elaborate dinner parties, this cooktop can rise to the occasion, making it an essential kitchen ally.
Top Page Image Contents