Installation

Electrical Requirements

GB For your own safety, we recommend that your cooker is installed by a competent person such as one who is registered with NICEIC (National Inspection Council for Electrical Installation Contracting). The cooker should be installed in accordance with the latest edition of the IEE Regulations.

Warning: This appliance must be earthed.

Electrical Connections

The installer must check that the voltage shown on the rating plate corresponds with the house electricity supply. The cooker must be supplied via a suitable double pole isolating switch, having a contact separation of at least 3mm in all poles placed in a readily accessible position adjacent to the cooker. If the cooker is to be wired into a connector unit, this may be positioned behind the cooker providing the following requirements are met:

i)The connector unit must not project from the wall more than 25mm.

ii)The top of the connector must not be more than

130mm above floor level.

Remove the terminal cover at the rear base of the cooker. Pass the cable through the cable clamp and connect to the appropriate terminals provided. Allow sufficient cable for any future servicing. Tighten the screws on the cable clamp and replace the cover. Make main connections in the connector unit or cooker control unit. This appliance conforms to B.S. EN 55014 regarding suppression of Radio and Television reception interference.

A double Pole control switch having a minimum rating of 32 amps should be used to feed the cooker using a suitably rated cable. Where a hob is fitted adjacent to or over the cooker, a 45 amp Double Pole control switch should be used to feed both units via separate suitably rated cables.

We recommend a minimum of 4mm2 PVC insulated twin and earth cable conforming to B.S. 6004 for connection of each appliance.

In all cases adhere to routing details (see fig. 4).

This appliance must not be installed over any other appliance that generates heat such as a plinth heater.

Note: Due to many different types of installation, a mains cable is not supplied with this product. The installer will fit the correct type and length of cable.

Important

It is essential that the lower cupboard is constructed in the manner illustrated i.e. having side, back, and roof panels so joined as to provide no apertures which could permit access to the oven unit when installed.

1.General

The appliance is designed for mounting at a safe level into an oven housing which must be secured to the backing wall.

2. Ventilation

a. The oven housing unit cabinet dimensions must comply with fig. 4.

b. An air gap of 50mm minimum must be provided at the rear of any top or bottom cupboards or shelves (see fig. 1).

c. It is necessary that the cabinets are provided with unobstructed ventilation, i.e. from adjacent cabinetry. This can be done by either raising the base of the cabinets using the adjusting feet (or spacers) or alternatively by providing a slot in the cabinet plinth to the dimensions in fig. 1.

d. The air gap at rear allows the warmed air to pass out of the inner cabinet space. Where it is intended to fit cupboards above the oven unit to ceiling height, it is essential that the warmed air is exhausted through the front of the cabinet (see fig. 1).

e. If an oven unit is installed adjacent to a tall cabinet, steam escaping from the oven when the door is opened could condense on and maybe stain the adjacent surface. To prevent permanent staining, the adjacent surface should be made of a material that is heat resisting and easy to clean. Adjacent tall cabinets should not be deeper than the oven housing cabinet.

3.Final Installation

a. Using a spirit level, check that the housing cabinet is level from side to side and from front to back in its installed position.

b. Correct any unevenness by placing spacers under the bottom of the cabinet. Make sure that the cabinet rests firmly on the floor without rocking.

c. Before the oven is fitted, the cabinet must be firmly secured to the backing wall for stability.

d. The oven unit should now be lifted (this is a two person lift) into the cabinet and pushed fully home. e. Finally, the oven is secured to the cabinet by means of the four Phillips C/SK Head screws - two through

each side trim.

f. Remove all packaging material from the grill and oven interior.

List of loose items:

4x Phillips C/SK Head No. 6 x 25mm screws.

22

Page 21 Page 23
Page 22
Image 22
Hotpoint BD42SS2, DY46X2, DY46K2, DY46W2, BD32K2, BD32P2, BD32B2 manual Installation
Page 21 Page 23

BD42SS, DY46W2, DY46X2, DY46K2, DY46K specifications

The Hotpoint BD32B, BD32P, BD42SS2, BD32K, and BD32B2 models are part of Hotpoint's impressive lineup of refrigeration solutions, designed for both functionality and style. These refrigerators stand out in the market due to their array of advanced features and reliable performance, making them ideal for modern households.

One of the standout features across these models is the No Frost technology, which prevents the build-up of frost and ice, ensuring that users never have to manually defrost their refrigerators. This not only saves time but also enhances the efficiency of the appliance by improving airflow and cooling consistency.

The Hotpoint BD32B features a spacious interior that includes adjustable shelves, providing flexibility for organizing food and beverages. With a generous storage capacity, families can easily store large quantities of groceries, making it practical for everyday use. The reversible door feature on these models allows for easy installation in different kitchen layouts, accommodating various consumer needs.

Energy efficiency is another hallmark of the Hotpoint BD series. These refrigerators are designed to consume minimal electricity, which not only helps in reducing utility bills but also promotes eco-friendliness. User-friendly controls, often featuring intuitive digital displays, make it easy to adjust temperatures and monitor settings on the BD32P and BD42SS2 models.

The BD32K model is particularly noted for its sleek design, which can seamlessly blend into kitchen aesthetics while providing impressive storage. Additionally, the antimicrobial interior ensures that the refrigerator stays fresh and hygienic, keeping food safe from harmful bacteria.

Hotpoint refrigerators are known for their reliability and durability, with robust construction that promises longevity. The inclusion of LED lighting in the cooling compartments enhances visibility while consuming less power, further contributing to the energy efficiency of the appliances.

Overall, the Hotpoint BD32B, BD32P, BD42SS2, BD32K, and BD32B2 models embody a perfect balance of innovative technology, spacious design, and energy-saving features, making them a valuable addition to any kitchen. Users can expect not only to meet their cooling needs but also to enhance their overall culinary experience with these thoughtfully designed refrigerators.
Top Page Image Contents