Troubleshooting
GB | Whenever the appliance fails to work properly, check for a solution from the following list before calling for Assistance. | ||
|
|
| |
|
|
|
|
|
|
|
|
|
| Problem: | Possible causes / Solutions: |
|
| The dishwasher does not start or cannot | • Switch off the appliance by pressing the ON/OFF button, switch it back |
|
| be controlled. | on after approximately one minute and reset the cycle. |
|
|
| • The appliance has not been plugged in properly. |
|
|
| • The dishwasher door has not been shut properly. |
|
| The door won’t close. | • The lock was released. Strongly push the door until a “clacking” noise is |
|
| heard. | |
|
| No water drains from the | • The dishwasher cycle has not yet finished. |
|
| dishwasher. | • The water drain hose is bent (see Installation.) |
|
|
| • The drain duct is blocked. |
|
|
| • The filter is clogged up with food residues. |
|
| The dishwasher makes excessive | • The dishes are rattling against each other or against the sprayer arms. |
|
| noise. | • An excessive amount of foam has been produced: the detergent has not |
|
|
| been measured out correctly or it is not suitable for use in dishwashers |
|
|
| (see |
|
| The dishes and glasses are | • The level of refined salt is low or the dosage setting is not suitable for |
|
| covered in a white film or | the hardness of the water (see Rinse aid and salt.) |
|
| limescale deposits. | • The lid on the salt dispenser is not closed properly. |
|
| • The rinse aid has been used up or the dosage is too low. | |
|
|
| |
|
| The dishes and glasses are | • The rinse aid dosage is too high. |
|
| streaked or have a bluish tinge. |
|
|
| The crockery has not been dried | • A wash cycle without a drying cycle has been selected. |
|
| properly. | • The rinse aid has been used up or the dosage is too low (see Rinse aid |
|
|
| and salt.) |
|
|
| • The rinse aid setting is not suitable. |
|
|
| • The crockery is made from |
|
| The crockery is not clean. | • The racks are overloaded (see Loading the racks.) |
|
|
| • The crockery has not been arranged well. |
|
|
| • The sprayer arms cannot rotate freely. |
|
|
| • The wash cycle is too gentle (see Wash cycles.) |
|
|
| • An excessive amount of foam has been produced: the detergent has not |
|
|
| been measured out correctly or it is not suitable for use in dishwashers |
|
|
| (see |
|
|
| • The lid on the rinse aid compartment has not been shut correctly. |
|
|
| • The filter is dirty or blocked (see Care and maintenance.) |
|
|
| • The refined salt level is low (see Rinse aid and salt.) |
|
| The dishwasher does not take | • There is no water in the mains supply. |
|
| any water in - Tap | • The water inlet hose is bent (see Installation.) |
|
| (short beeps are heard)* | • Turn on the tap and the appliance will start after a few minutes. |
|
| (the ON/OFF indicator light flashes, | • The appliance lock has been activated because no action was taken |
|
| when the beeps sounded. | |
|
| the “Tap | |
|
| Switch off the machine using the ON/OFF button, turn on the tap and | |
|
| and the display shows the text: | switch the machine back on after a few seconds by pressing the same |
|
| No water. Turn tap on. After a few | button. |
|
| seconds F 06 appears.) |
|
|
| Water inlet hose alarm / Water | • Switch off the appliance by pressing the ON/OFF button. Shut off the |
|
| inlet filter blocked | water tap to eliminate the risk of flooding and remove the plug from the |
|
| (the ON/OFF indicator light flashes, the | electrical socket. |
|
| Make sure the water inlet filter has not become blocked by impurities | |
|
| “Filter” symbol is lit and the display shows | |
|
| (see “Care and maintenance” chapter.) | |
|
| the textF 07.) | |
|
|
|
*Only available in selected models.
16