GB

 

 

The Company shall not be held responsible for any

 

 

incidents that occur if these regulations are not observed.

 

Anti-condensation strip*

After installing the dishwasher, open the door and stick the adhesive transparent strip under the wooden shelf in order to protect it from any condensation which may form.

Technical data

Dimensions

width 60 cm

height 85 cm

 

 

 

depth 60 cm

Capacity

13 standard place-settings

Water supply

0,05 ÷ 1MPa (0.5 ÷ 10 bar)

pressure

7,25 – 145 psi

Power supply voltage

See appliance data plate

 

 

 

 

Total absorbed power

See appliance data plate

 

 

 

 

Fuse

See appliance data plate

 

 

 

This dishwasher conforms to the

 

 

 

following European Community

 

 

 

Directives:

 

 

 

-2006/95/EC (Low Voltage)

 

 

 

-2004/108/EC (Electromagnetic

 

 

 

Compatibility)

 

 

 

-2009/125/EC (Comm. Reg.

 

 

 

1016/2010) (Ecodesign)

 

 

 

-97/17/EC (Labelling)

 

 

 

-2012/19/EU Waste Electrical

 

 

 

and Electronic Equipment

 

 

 

(WEEE)

 

 

 

Connecting the water supplies

Connection to the water and electricity supplies should only be performed by a qualified technician.

The dishwasher should not stand on top of the water hoses or the electricity supply cable.

Connecting the water inlet hose

The water inlet and outlet hoses and the electricity supply cable may be positioned towards the right or the left in order to achieve the best possible installation.

To a suitable cold water connection point: before attaching the hose, run the water until it is perfectly clear so that any impurities that may be present in the water do not clog the appliance; after performing this operation, screw the inlet hose tightly onto a tap with a ¾ gas threaded connection.

To a suitable hot water connection point: your dishwasher may be provided with hot water from the mains supply (if you have a central heating system with radiators) provided that it does not exceed a temperature of 60°C.

Screw the hose to the tap as described for connection to a cold water supply.

If the inlet hose is not long enough, contact a specialist store or an authorised technician (see Assistance).

The water pressure must be within the values indicated in the Technical data table (see Installation).

The hose should not be bent or compressed.

The appliance must be connected to the water supply network using new hoses.

Do not use old hoses.

Ensure that the new hose supplied is connected and the old hose is disposed of safely.

DO NOT overtighten the hose connector, hand tight is sufficient.

Ensure the fill hose is not kinked.

Tap connections*: A range of adaptors are available to suit your tap.

DO NOT connect the dishwasher to a single outlet instantaneous water heater or an electric heater.

Sink Waste System

Connect the outlet hose (without bending it) to a drain duct with a minimum diameter of 32 mm.

The outlet hose must be at a height ranging from 40 to 80 cm (from 15’’ to 31’’) from the floor/surface where the dishwasher rests (A).

before connecting the drain hose, remove any internal restrictions; this will prevent a build up of debris which could cause a blockage

remove any restrictions from the waste spigot and ensure that the sealing bung is removed (B).

It MUST NOT be connected to a surface water drain.

Untie the end of the GREY drainage hose from the rear of the appliance.

If fitting an under sink waste disposal unit, cut out the membrane, bung or blanking plug.

*Only available in selected models.

6

Page 6
Image 6
Hotpoint FDYB 10011, FDYB 11011 manual Connecting the water supplies, Sink Waste System, Anti-condensation strip

FDYB 11011, FDYB 10011 specifications

The Hotpoint FDYB 10011 and FDYB 11011 are innovative dishwashers designed to enhance the efficiency of modern kitchens. These models are part of Hotpoint's commitment to combining style, functionality, and energy efficiency in their appliance lineup.

Both the FDYB 10011 and FDYB 11011 come equipped with several main features that make them stand out in the crowded dishwasher market. One of the key attributes of these models is their spacious interior, which can accommodate up to 13 place settings. This means that families or those who entertain frequently will find these dishwashers particularly advantageous, as they can handle larger loads without the need for multiple cycles.

The energy efficiency of the FDYB 10011 and FDYB 11011 is another highlight, as both models boast impressive energy ratings, making them cost-effective choices for consumers. These dishwashers are designed to use less water and electricity, reducing the environmental impact while still delivering powerful cleaning performance.

In terms of technology, both models feature the innovative "Eco Technology," which optimizes water consumption and energy use during wash cycles. This means less waste without compromising cleaning effectiveness. Additionally, the "Hygiene" program is a notable inclusion that uses higher temperature settings to provide a deeper clean, killing up to 99.9% of bacteria on dishes – a significant feature for households with young children or those concerned about hygiene.

The "Intensive" wash program is another advantage, perfect for heavily soiled pots and pans. It ensures that even the toughest stains are dealt with efficiently, making post-meal cleanup easier than ever.

The design of the FDYB 10011 and FDYB 11011 is sleek and modern, fitting seamlessly into any kitchen decor. The control panel is user-friendly, featuring intuitive touch controls that make program selection straightforward.

In summary, the Hotpoint FDYB 10011 and FDYB 11011 dishwashers offer a blend of spaciousness, energy efficiency, advanced technology, and user-friendly design. With their powerful cleaning capabilities and innovative features, they cater to the needs of busy households, ensuring that dishwashing becomes a hassle-free task.