HOT PARTS mm600

Installation

Moving the Cooker

GB

Fig. B

Fig. C

 

Gas connection

 

The cooker should be connected to the gas-supply by a corgi registered installer. During installation of this product it is essential to fit an approved gas tap to isolate the supply from the appliance for the convenience of any subsequent removal or servicing. Connection of the appliance to the gas mains or liquid gas must be carried out according to the prescribed regulation in force, and only after it is ascertained that it is adaptable to the type of gas to be used. If not, follow the instructions indicated in the paragraph headed “Adaptation to different gas types”. On some models the gas supply can be connected on the left or on the right, as necessary; to change the connection, reverse the position of the hose holder with that of the cap and replace the gasket (supplied with the appliance). In the case of connection to liquid gas, by tank, use pressure regulators that conform to the regulation in force. The gas supply must be

connected to the

left of the appliance.

Be sure that the

hose does not pass

through the rear of

the cooker touching hot parts.

! Make sure the supply pressure

conforms with the values shown in the table entitled “Caracteristics of the burners and nozzles”.

When the cooker is installed between cabinets (recessed), the gas connection must be effected by an approved flexible hose with bayonet fitting (BS 669 Current Edition). The gas inlet for the cookers is a threaded G 1/2 gas female fitting.

Connecting the gas supply

To make the connection, a flexible hose should be used corresponding to the current gas regulations which are:

•the hose must never be at any point in its lenght in contact with the “hot” parts of the cooker;

•the hose must never be longer than 1,5 metre;

•the hose must not be subject to any tension or torsional stress and it must not have any excessively narrow curves or bottlenecks;

•the hose must be easy to inspect along its entire length to check its condition;

•the hose must always be in good condition, never attempt to repair.

!The installation must comply with gas safety (installation and use) regulations 1984. In all cases for the above, by low, a qualified, corgi approved engineer must be called for installation.

Disposing of the appliance

When disposing of the appliance please remove the plug by cutting the mains cable as close as possible to the plug body and dispose of it as described above.

Adapting the cooker to different types of gas

In order to adapt the cooker to a different type of gas with respect to the gas for which it was produced (indicated on the label attached to the lid), follow these steps:

a)replace the hose holder mounted on the appliance with that supplied in the bag of “cooker accessories”.

b)Replacing the burner nozzles on the hob:

•remove the grids and slide the burners from their housings;

•unscrew the nozzles using a 7 mm socket spanner, and replace them with

nozzles for the new type of gas (see table 1 “Burner and nozzle characteristics”).

• replace all the components by repeating the steps in reverse order.

6 PLEASE PHONE US TO REGISTER YOUR APPLIANCE AND ACTIVATE YOUR PARTS GUARANTEE ON 08448 24 24 24

Page 5 Page 7
Page 6
Image 6
Hotpoint HAGL 51 P, HAGL 51 K, 50cm Gas Cooker Gas connection, Connecting the gas supply, Disposing of the appliance
Page 5 Page 7

HAGL 51 K, HAGL 51 P, 50cm Gas Cooker specifications

The Hotpoint HAGL 51 P and HAGL 51 K models are versatile 50cm gas cookers designed to enhance your kitchen experience while providing exceptional cooking performance. These cookers blend functionality, style, and efficiency, making them ideal for both novice cooks and seasoned chefs.

One of the standout features of the Hotpoint HAGL 51 series is its compact design, which makes it perfect for smaller kitchens without compromising cooking capacity. With four gas burners, including a powerful wok burner, users can enjoy precise heat control and flexibility. The burners are designed to accommodate various cooking styles, from simmering sauces to rapidly boiling water.

Both models are equipped with a fan-assisted gas oven, ensuring even cooking results throughout the cavity. The eye-level grill function adds versatility, allowing users to grill up delicious meals without needing a separate appliance. This feature is particularly handy for those who enjoy preparing crispy dishes or melting cheese to perfection.

Safety is a priority with the Hotpoint HAGL 51 series, featuring flame failure devices that automatically cut off the gas supply if a flame goes out. This provides peace of mind, especially in households with children. Furthermore, the easy-clean oven lining makes maintaining hygiene simple, allowing food residue to be wiped away with minimal effort.

Cooking efficiency is enhanced through the inclusion of a double-glazed oven door, which helps retain heat while keeping the exterior cool to the touch. This not only enhances energy efficiency but also ensures that your kitchen remains comfortable during cooking sessions.

In terms of aesthetics, the HAGL 51 P presents a clean white finish, while the HAGL 51 K offers a sleek black look, allowing users to choose a design that complements their kitchen decor. Both cookers feature ergonomic controls, easy to read markings, and smooth operation for a user-friendly experience.

In summary, the Hotpoint HAGL 51 P and HAGL 51 K gas cookers deliver a balanced blend of style, technology, and practicality. With their compact design, versatile burners, fan-assisted oven, safety features, and easy maintenance, these models prove to be an excellent choice for any kitchen setting. Whether you’re baking, boiling, or grilling, these cookers stand ready to support your culinary creations efficiently and safely.
Top Page Image Contents