Manuals / Hotpoint / Kitchen Appliance / Range

Hotpoint JB400DP1WW Plano Safety Glasses Steel Toe Shoes Dyneema Cut, ANSI Z87.1-2003, Copyright

Models: JB400DP1BB JB400SPSS JB400DP1WW

1 57

Page 3

GE Factory Service Employees are required to use safety glasses with side shields, cut resistant (Dyneema®) gloves & steel toe shoes for all repairs.

Plano Safety Glasses

Steel Toe Shoes

Dyneema® Cut

Resistant Glove

Prescription Safety Glasses

Safety Glasses must be compliant with

ANSI Z87.1-2003

Page 3

Image 3

Hotpoint JB400DP1WW manual Plano Safety Glasses Steel Toe Shoes Dyneema Cut, Resistant Glove Prescription Safety Glasses

Contents

Range Models GE JB400 Steam Clean RangeIMPORTANT SAFETY NOTICE RECONNECT ALL GROUNDING DEVICESCopyright ANSI Z87.1-2003 Plano Safety Glasses Steel Toe Shoes Dyneema CutResistant Glove Prescription Safety Glasses Safety Glasses must be compliant withCopyright WarrantyCopyright NomenclatureJ B 400 D P 1 WW J = GEModel / Serial Number Plate Copyright Anti-TipBracketOven Door Removal •Fully open the doorCopyright Copyright •Close door to the door removal position•Firmly grasp both sides of the door at the top Oven Door Removal•Firmly grasp both sides of the door at the top Oven Door Re-InstallationCopyright •Close the oven doorOven Door Re-Installation •Fully open the doorCopyright Door GasketCopyright Door GasketDoor Switch Copyright Door Switch Replacement•Use prop to support cooktop, if desired Cooktop•Open oven door •Lift cooktop1500W Cooktop Elements8 Inch 2000W 6 Inch 1500W 10Inch 3000W Inner – 1400W Outer – 1600W 6 InchCopyright Cooktop Element Replacement•Disengage mounting clips from burner case Cooktop Element ReplacementMark and remove wires from terminals •Lift and remove burner from cooktop assemblyCopyright Temperature Limit / Hot Cooktop Light Switch2.Detects when glass temperature above a unit has exceeded it’s limit of approximately 1031F and disconnects power to that unit. When the glass temperature cools below 1031F, the unit will turn back on Temperature Limit / Hot Cooktop Light SwitchCooktop Removal Copyright Cooktop Removal•Return cooktop to normally closed position •Lift rear of cooktop @ two inchesControl Panel Removal Copyright Control Panel Removal3.Pull bottom of panel out while lifting panel up 4.Lay panel on cooking surfaceOven Sensor Oven Sensor Oven sensor disconnect plugCopyright 2:31 T09 Control - ERCDisplay On / Off Feature 3:02Copyright Copyright Special FunctionsT09 Control – ERC Removal •Remove ERC from frameCopyright Broil Element 2 white - Sensor Orange / Yellow - Door SwitchT09 Control - ERC Oven LightKey Panel Test 3:02•Clock – Audible tone and display change Copyright Control Voltage - ERCConditions & Fault CodesFunction Key sCopyright Fault CodesSteam Clean Operation 0:30Copyright Steam Clean Procedure To begin the steam cycle3.Close the door Copyright Steam Clean Procedure4.Press the Steam Clean pad; then press Start/On 0:3010.Leave the door open to air dry Steam Clean ProcedureSteam Clean Procedure – IMPORTANT NOTES Hidden Bake Element Hidden Bake Element •If element requires replacement, range left side panel needs to be removedCopyright Hidden Bake ElementCopyright Hidden Bake ElementCopyright Hidden Bake ElementCopyright Hidden Bake ElementCopyright Hidden Bake Element•Remove orange and yellow leads from bake element terminals Hidden Bake ElementCopyright Hidden Bake ElementHidden Bake Element Slide out element from compartment to removeCopyright Copyright Hidden Bake ElementCopyright Oven LightCopyright Strip CircuitsCopyright SchematicCopyright Wiring DiagramCopyright END OF PRESENTATION