Installation
Electrical Requirements
GB For your own safety, we recommend that your cooker is installed by a competent person such as one who is registered with NICEIC (National Inspection Council for Electrical Installation Contracting). The cooker should be installed in accordance with the latest edition of the IEE Regulations.
Warning: This appliance must be earthed.
Electrical Connections
The installer must check that the voltage shown on the rating plate corresponds with the house electricity supply. The cooker must be supplied via a suitable double pole isolating switch, having a contact separation of at least 3mm in all poles placed in a readily accessible position adjacent to the cooker. If the cooker is to be wired into a connector unit, this may be positioned behind the cooker providing the following requirements are met:
i)The connector unit must not project from the wall more than 25mm.
ii)The top of the connector must not be more than
130mm above floor level.
Remove the terminal cover at the rear base of the cooker. Pass the cable through the cable clamp and connect to the appropriate terminals provided. Allow sufficient cable for any future servicing. Tighten the screws on the cable clamp and replace the cover. Make main connections in the connector unit or cooker control unit. This appliance conforms to B.S. EN 55014 regarding suppression of Radio and Television reception interference.
A double Pole control switch having a minimum rating of 32 amps should be used to feed the cooker using a suitably rated cable. Where a hob is fitted adjacent to or over the cooker, a 45 amp Double Pole control switch should be used to feed both units via separate suitably rated cables.
We recommend a minimum of 4mm2 PVC insulated twin and earth cable conforming to B.S. 6004 for connection of each appliance.
In all cases adhere to routing details (see fig. 5).
This appliance must not be installed over any other appliance that generates heat such as a plinth heater.
Note: Due to many different types of installation, a mains cable is not supplied with this product. The installer will fit the correct type and length of cable.
GENERAL
The appliance is designed to be mounted on a floor between two adjacent cabinets.
The cabinets must be securely fixed to the wall and the cooker securely fixed to the cabinets.
This cooker must not be used free standing. Note; This cooker must not be fitted on a platform.
FINAL INSTALLATION
a.Ensure that the adjacent cabinets and the gap between them have dimensions in accordance with the diagram.
b.Assemble the plastic plugs provided into the fixing brackets. See diagram.
c.Fix the fixing brackets to the sides of the adjacent cabinets so that the centre line of the brackets are 570mm above the top of the plinth line and the front face of the plastic plug is level with the front face of the cabinet sides. See diagram.
d.Adjust the feet on the cooker to their minimum position, i.e. fully screwed in.
e.Slide the cooker centrally into the space between the cabinets ensuring the following:
i)The gap between the cabinet sides and the cooker is even along the length of the cabinet sides.
ii)The cable is routed away from any vents in the rear panel and is not trapped between the cooker and the wall, adjacent cabinets or under the feet
f.Adjust the feet using an open ended spanner until the bottom of the cooker door is in line with the top of the plinth. Using a spirit level, check that the cooker is level in all directions.
g.Check that the plinth can be fitted. If necessary re - adjust the feet and check that the cooker is level. Then lock the feet into position by tightening the lock nut using an open ended spanner.
h.Open the top oven door and fix the cooker to the brackets through the holes in the side trims.
i.Fix the plinth in position.
j.Ensure that there is a minimum gap of 1mm between the cooker side trim and the adjacent cabinet doors or drawer fronts.
k.If a hob is to be installed directly above the cooker it must not project downwards more than 20mm below the underside of the work top. Any projection of more than 10mm must not project more than 500mm from the wall.
Fig. 5
24
