U Series 5™ Family Installation Guide

ST340823A, ST330621A, ST320413A, ST315311A, ST310211A

Publication Number: 21200248-001, Rev. A

The Easiest Way to Install Your Drive

DiscWizard™ is Seagate’s exclusive Windows program that is included with your drive for easy drive installation. You can use this software if you have a bootable hard drive in your computer and are running Windows 95 or 98.

Run DiscWizard before installing your drive for customized step-by-step instructions for your system.

To run DiscWizard:

•Select Run from the Windows Start menu and type x:\setup, where x is the drive letter of your CD-ROM.

If you cannot run DiscWizard, follow the instructions on this installation sheet to install and configure your drive.

What You Need

•Phillips screwdriver and four 6-32 UNC drive mounting screws

•A standard 40-pin ATA interface cable, or an 80-conductor cable to run Ultra ATA 100 (max length: 18 inches)

•An unused drive power cable for your new drive
•Windows 98 to support drives greater than 33.8 Gbytes

Ultra ATA/100 Requirements

The drive can support transfer rates up to 100 Mbytes per second (UDMA 5) in Ultra ATA/100 mode. For your drive to run in this mode, you need the following:

•A computer that supports UDMA mode 5
•A 40-pin 80-conductor cable (available from your dealer)

•A software utility to confirm and activate Ultra ATA/100. Seagate® provides a utility called UATA100.exe. You can download the latest version from our Web site at www.seagate.com.

•The Windows 98 operating system

Handling Precautions

Disc drives are extremely fragile. Do not drop or jar the drive.

Keep the drive in the protective SeaShell™ container until you are ready to install it. This minimizes handling damage.

The drive has a protective cover called SeaShield®. Do not remove this permanent cover—it protects the drive from electrostatic discharge (ESD) and minor impact damage.

Protect your drive from static discharge by wearing a grounded wrist strap throughout the installation process.

Always handle the drive by the edges or frame.

Do not apply pressure or attach labels to the circuit board or the top of the drive.

Setting the Jumpers

Refer to the jumper settings below to configure the drive for your system.

Options jumper block

Master or single drive

Drive is slave

Master with non ATA- compatible slave

Cable select

Limit drive capacity

40 Gbytes = 32 GB

<40 Gbytes = 2.1 Gbytes

7 5 3 1

 

 

 

 

 

 

 

8

6

4

2

 

 

 

Circuit Board

 

 

 

 

 

•Master or single-drive:The drive is shipped configured for a master or a single drive with a jumper set on pins 7 and 8.

•Drive is slave: To configure the drive as a slave, or second drive on the cable, remove all the jumpers.

•Master with non-ATA compatible slave: Use this setting if the slave drive is not recognized. Configure the master drive with a jumper set on pins 5 and 6 and pins 7 and 8 to enable this option.

•Cable-select option: Computers that use cable-select determine the master and slave drives by selecting or deselecting pin 28, CSEL, on

the interface bus. To enable cable select, set a jumper on pins 5 and 6.

•Alternate capacity jumper: Drives with a 40-Gbyte capacity are limited to 33.8 Gbytes. Drives with 30 Gbytes or less are limited to 2.1 Gbytes.

Attaching Cables and Mounting the Drive

1.Attach one end of the drive interface cable to the interface connector on your computer’s motherboard (see your computer manual for connector locations).

 

Note. If you are using a 40-pin 80-conductor

Master

 

cable, attach the blue connector to the

Pin 1

motherboard, the black connector to the

 

 

master drive, and the grey connector

 

Computer

Slave

to the slave.

 

Motherboard

 

!Caution. Align pin 1 on the motherboard connector with pin 1 on your drive connector. Pin 1 is marked by a stripe on one side of the cable.

Power connector

Interface connector

Pin 1

2.Attach the interface connector and the power connector to the drive.

Note. You can mount the drive in any orientation. Usually it is mounted with the circuit board down.

3.Secure the drive in the computer using four 6-32 UNC mounting screws in either the side-mounting or bottom-mounting holes. Insert the screws no more than 0.20 inch (5.08 mm) into the bottom-mounting holes and no more than 0.14 inch (3.55 mm) into the side-mounting holes.

!Caution. Do not overtighten the screws or use metric screws. This may damage the drive.

Configuring the BIOS

For your computer to recognize your new drive, configure your computer’s BIOS as follows:

1. Run the system setup program.
2. Enable LBA mode and UDMA mode, if available.

3. Select the auto-detect option. If this is not available, select “User- defined drive type” and enter the CHS (cylinder, head, sectors) parameters for your drive from the table listed below. The CHS addressing supports capacities up to 8.4 Gbytes only. To access the full capacity of the drive, use LBA mode.

4.Save and exit the system setup program.

 

 

BIOS Settings

 

 

 

CHS Mode

 

LBA Mode
Drive Model
Cylinders
Heads
Sectors
Total Sectors*
ST340823A

16,383

16

63

78,165,360

ST330621A

16,383

16

63

58,633,344

ST320413A

16,383

16

63

39,102,336

ST315311A

16,383

16

63

29,336,832

ST310211A

16,383

16

63

19,541,088

*One sector equals 512 bytes.