HP A710 INSTALLATION, III. OPERATION, ENGLISH, “OFF”, raise, lower, Figure, Figure, WARNING, WARNING, IMPORTANT, Placement, IMPORTANT, clockwise, Daily Cleaning

		II.	INSTALLATION
		IMPORTANT
		IT IS THE CUSTOMER’S RESPONSIBILITY TO REPORT ANY
		CONCEALED OR NON-CONCEALED DAMAGE TO THE FREIGHT
		COMPANY.
		A.	Placement
ENGLISH		Check that the four 5/8” (16mm) rubber feet are installed. Then,
		position the sandwich grill in place.
	3.		If your grill is has grill plates with a natural aluminum finish,
		B.	Initial Cleaning
	1.		Ensure that any packing material has been removed.
	2.		Follow the procedure in Section IV, Daily Cleaning, to perform
			an initial cleaning of the grill. Be sure to thoroughly clean the top
			and bottom grill plates, AND the exterior of the grill.
			condition the grills with a thin coating of cooking oil or shortening.
			If your grill has a DuPont SilverStone Supra® coating, it is not
			necessary to season the non-stick surface.
		C.	Electrical Utility Connection
		IMPORTANT
		THE ELECTRICAL CONNECTION TO THE SANDWICH GRILL RE-
		QUIRES A CIRCUIT BREAKER/FUSED DISCONNECT. ELECTRI-
		CAL SPECIFICATIONS ARE LISTED ON THE SERIAL PLATE (LO-
		CATED ON THE REAR OF THE SANDWICH GRILL), AND ON THE
		WIRING DIAGRAMS AT THE BACK OF THIS MANUAL.
		CONSULT ALL APPLICABLE NATIONAL AND LOCAL CODES FOR
		FURTHER ELECTRICAL CONNECTION REQUIREMENTS.
		1.	Before proceeding with the electrical connection, check the fol-
			lowing:
			a. Check that the electrical supply matches the sandwich grill’s
			requirements. Refer to the serial plate (on the rear of the
			unit) and to the electrical specifications at the back of this
			Manual.
			b. Check that the appropriate receptacle is available for the
			power cord plug.
			WARNING
			ENSURE THAT BOTH THE CIRCUIT BREAKER/FUSED DIS-
			CONNECT AND THE THREE-POSITION POWER SWITCH
			ARE IN THE “OFF” (O) POSITION BEFORE PROCEEDING.
			WARNING
			ENSURE THAT ANY PACKING MATERIAL HAS BEEN RE-
			MOVED FROM THE TOP AND BOTTOM GRILL PLATES.
	3.		Insert the power cord plug into its receptacle.

1. Closure height	Figure 2
adjustment knob
2. Closure
height
locking
knob

3. Temperature	4. “BOTH/OFF/
adjustment knob	BOTTOM” switch

III. OPERATION

A.Location and Function of Controls

This section provides a basic description of the sandwich grill’s controls, their location, and the functions they perform. The operator MUST be familiar with the controls. See Figure 2.

1.Closure height adjustment knob

Adjusts the spacing between the top and bottom grill plates to accomodate food products of different thicknesses.

2.Closure height locking knob

When tightened, prevents the Closure Height Adjustment Knob from being turned. When loosened, allows the Closure Height Adjustment Knob to be turned.

3.Temperature adjustment knob

Adjusts the temperature setting of the heating element(s). This controls the temperature of the grill plates.

To change the temperature setting, turn the knob until the desired temperature is aligned with the arrow above the knob.

4.Three-position power switch

•When set to “ON BOTTOM GRID,” turns on the heating element for the bottom grill plate ONLY.

•When set to “OFF” (O), turns off both of the heating elements.

•When set to “ON TOP/BOTTOM GRIDS,” turns on the heating elements for the top AND bottom grill plates.

B.Operation Procedure

1.If necessary, adjust the closure height of the top grill plate as described below. Refer to Figure 3.

•Check that the top grill plate is lowered.

•Loosen the closure height locking knob.

•Turn the closure height adjustment knob as necessary to raise or lower the top grill plate to the correct height. See Figure 3.

-Turn the knob clockwise to raise the top grill.

-Turn the knob counterclockwise to lower the top grill.

If necessary, place a sample of the food product between the grill plates to check for the correct spacing.

•When the top grill plate is at the proper height, tighten the closure height locking knob.

Figure 3

4		3
		Turn adjustment knob
	Raise
Tighten		to reposition top grill
locking knob	grill
		Lower
	2	grill
	Loosen
	locking knob

1

Check that top

grill plate is

lowered