Manuals / Brands / Computer Equipment / Laptop / HP / Computer Equipment / Laptop

HP Armada E700 Result Code Control, Sn Read/Write an S-Register, Display Online Help for S-Registers, Result Code Form

1 33

Download 33 pages, 66.89 Kb

Compaq Global Mini PCI 56k (V.90) Modem by 3Com		15
		White Paper
Qn	Result Code Control

Result codes are informational messages sent from the modem and displayed on your monitor. Basic result codes are OK, CONNECT, RING, NO CARRIER, and ERROR. Also sometimes referred to as "quiet" mode, the Q setting controls the level of result codes generated by the modem.

Q0 Display result codes (default).

Q1 Quiet mode; no result codes.

Q2 Displays result codes only in Originate Mode.

Result Codes:
OK	n = 0 - 2.
ERROR	Otherwise.

Sn Read/Write an S-Register

Sets the register r to the specified value n.

The Sr? command reads (displays) the value in register r.

Q$	Display the list of S-register settings.
Qr=n	Set S-register "r" to "n".
Qr$	Display the value of S-register "r".
Result Codes:
	OK	n = $, r = n, r$.
	ERROR	Otherwise.

S$	Display Online Help for S-Registers
	Displays online Help for S-registers.
Vn	Result Code Form

Determines the type of result code. The V command determines if the result code is sent as words or numbers.

V0 Display result codes in numeric form.

V1 Display result codes in verbose form (words).

Result Codes:
OK	n = 0, 1.
ERROR	Otherwise.

	ATV0	ATV1

Result Code Format	<numeric code><CR>	<CR><LF>
		<verbose code><CR><LF>

0203-0799-A

Contents

White Paper Compaq Global Mini PCI 10/100 LAN + 56k (V.90) Modem by 3Com Notice Using Modem Commands Entering a Command Editing and Executing a Command Omitting a Parameter in a Command Line Repeating a Command Understanding Result Codes Using Online Mode Escaping from an Online Session to the Command Mode Creating a Command Mode Shortcut Creating a Command Mode Icon AT Command Set AT Data Command Set Summary Result Code Summary Page AT Command Descriptions +++Escape sequence Display AT Command List Repeat Last Command AAnswer Command Dn Dial En Character Echo Command Fn Online Echo Command Hn Hook Control Request Identification/Checksum Page Page Ln Speaker Volume Mn Speaker Control On Online Data Mode Result Code Control Sn Read/Write an S-Register Display Online Help for S-Registers Result Code Form Xn Result Code Select Power-On/ResetDefault Configuration Reset and Recall Stored Profile &$ Display Online Help for Ampersand Commands &An Result Code Control &Bn DTE Speed &Cn Data Carrier Detect (DCD) Control &Dn Data Terminal Ready (DTR) Control &Fn Load Factory Settings &Gn Guard Tone Control &Hn Flow Control for Transmitted Data &In Flow Control for Received Data &Kn Data Compression Control &Mn Error Correction Control &Nn Link Speed Control &Rn RTS Control &Sn Data Set Ready (DSR) Option &Un Link Rate &Wn Store Active Profile &Yn Set Break Handling &Zn Store Telephone Number S Registers Setting S Register Default Values Modifying an S Register Reading an S Register S-RegisterSummary S-RegisterDescriptions S0 Ring to Answer On S1 Ring Count S2 Escape Code Character S3 Carriage Return Character S5 Backspace Character S6 Wait for Blind Dial S7 Wait Time for Carrier S8 Pause Time for Comma S9 Carrier Detect Validation Time S10 Lost Carrier to Hang-UpDelay S11 Touch-ToneSpacing S12 Escape Code Guard Time S13 Bitmapped Register S15 Bitmapped Register S16 Bitmapped Test Register S18 Test Timer S19 Inactivity Timer S21 Error Correction Break Length S22 Character Code for XON S23 Character Code for XOFF S25 Response to DTR Change S27 Bitmapped Register S28 V.32 Handshake Time S29 V.21 Answer Mode Fallback Timer S32 Connection Bitmapped Operations S33 V.34 Connection Setup Control Flags S34 V.34 Connection Setup Control Flags S38 Delay Before Forced Hang-up