Manuals / Brands / Computer Equipment / Laptop / HP / Computer Equipment / Laptop

HP Armada E700 S21 Error Correction Break Length, S22 Character Code for XON, S23 Character Code for XOFF, S25 Response to DTR Change

1 33

Download 33 pages, 66.89 Kb

Compaq Global Mini PCI 56k (V.90) Modem by 3Com

White Paper

S21 Error Correction Break Length

Sets the length, in 10-millisecond units, of breaks sent from the modem to the computer; applies to MNP or V.42 mode only.

Range: 0 - 255

Default: 1

Units:

0.01 seconds

S22 Character Code for XON

Stores the ASCII code for the XON character.

Range: 0 - 127

Default: 17

Units: ASCII

S23 Character Code for XOFF

Stores the ASCII code for the XOFF character.

Range: 0 - 127

Default: 19

Units: ASCII

S25 Response to DTR Change

Responds to changes to the DTR. The increment is 10 milliseconds. If &D1 or &D2 is selected, a change in DTR shorter than the S25 time is ignored. If &D3 is selected, any on-to-off transition of DTR causes a hard reset.

Range: 0 - 255

Default: 0

0203-0799-A

Contents

White Paper Compaq Global Mini PCI 10/100 LAN + 56k (V.90) Modem by 3Com Notice Using Modem Commands Entering a Command Editing and Executing a Command Omitting a Parameter in a Command Line Repeating a Command Understanding Result Codes Using Online Mode Escaping from an Online Session to the Command Mode Creating a Command Mode Shortcut Creating a Command Mode Icon AT Command Set AT Data Command Set Summary Result Code Summary Page AT Command Descriptions +++Escape sequence Display AT Command List Repeat Last Command AAnswer Command Dn Dial En Character Echo Command Fn Online Echo Command Hn Hook Control Request Identification/Checksum Page Page Ln Speaker Volume Mn Speaker Control On Online Data Mode Result Code Control Sn Read/Write an S-Register Display Online Help for S-Registers Result Code Form Xn Result Code Select Power-On/ResetDefault Configuration Reset and Recall Stored Profile &$ Display Online Help for Ampersand Commands &An Result Code Control &Bn DTE Speed &Cn Data Carrier Detect (DCD) Control &Dn Data Terminal Ready (DTR) Control &Fn Load Factory Settings &Gn Guard Tone Control &Hn Flow Control for Transmitted Data &In Flow Control for Received Data &Kn Data Compression Control &Mn Error Correction Control &Nn Link Speed Control &Rn RTS Control &Sn Data Set Ready (DSR) Option &Un Link Rate &Wn Store Active Profile &Yn Set Break Handling &Zn Store Telephone Number S Registers Setting S Register Default Values Modifying an S Register Reading an S Register S-RegisterSummary S-RegisterDescriptions S0 Ring to Answer On S1 Ring Count S2 Escape Code Character S3 Carriage Return Character S5 Backspace Character S6 Wait for Blind Dial S7 Wait Time for Carrier S8 Pause Time for Comma S9 Carrier Detect Validation Time S10 Lost Carrier to Hang-UpDelay S11 Touch-ToneSpacing S12 Escape Code Guard Time S13 Bitmapped Register S15 Bitmapped Register S16 Bitmapped Test Register S18 Test Timer S19 Inactivity Timer S21 Error Correction Break Length S22 Character Code for XON S23 Character Code for XOFF S25 Response to DTR Change S27 Bitmapped Register S28 V.32 Handshake Time S29 V.21 Answer Mode Fallback Timer S32 Connection Bitmapped Operations S33 V.34 Connection Setup Control Flags S34 V.34 Connection Setup Control Flags S38 Delay Before Forced Hang-up