“OUT” with 2/3 cable off reel–
SPRING
BROKEN
Figure 3
BROKEN SPRING
INDICATORS
“IN” with 2/3 cable off reel–
SPRING OK

INSTALLATION and MAINTENANCE INSTRUCTIONS

MMD28 DIRECT DRIVE ELECTRIC CABLE REELS

All units are provided with right hand rotation unless otherwise specified. This means that cable is pulled off spool top left or bottom right (spool rotates clockwise to wind cable) when viewing spring end of reel. See diagram on parts page.

Clock-type springs provide power for automatic cable take-up. Spring must be pretensioned at time of installation to insure that tension is applied to cable at all times. A tension adjustment spanner wrench is provided with each reel.

WARNING

Some reels with large or multiple springs are equipped with a ratcheted adjustment wrench. Follow separate instruc- tions for its use. Failure to use ratcheted wrench, on reels so equipped, could result in serious personal injury.

WARNING

Do not attempt to relieve spring tension using span- ner wrench. Doing so may result in personal injury.

INSTALLATION

1.Insure that machinery to be serviced by reel is at position closest to reel.

2.Securely mount reel in desired position using 3/8"(M10) bolts. Be sure spool is aligned with cable run.

3.Position optional cable guide, if reel is so equipped. See CABLE INSTALLATION DRAWING.

4.Connect free end of cable to junction box on machine or adjust cable stop so that desired length of cable extends from reel.

5.Remove cover plate on spring housing to expose shaft and spring hub. (See Figure 1).

6.Insert spanner wrench into holes in spring hub (Fig 2). Rotate wrench counterclockwise (for standard rotation). Number of 360O turns should match last digit in model number on serial plate. If model number includes an “R”, reel is reverse rotation and wrench must be rotated clockwise. (See EXPLANATION on parts list page.)

MAINTENANCE

Periodically: A. Use compressed air to clean collector assembly and inside of collector housing. Inspect collector assembly for brush wear and pitted slip rings.

B. Inspect cable for wear and check mounting bolts and

other hardware for tightness.

C. Check for broken springs

by pulling about 2/3 cable off

reel and observing “Broken

Spring Indicators” on sides of

spring canisters. See Fig. 3.

NOTE: Bearings and springs are prelubricated and require no periodic maintenance.

SPRING REPLACEMENT

WARNING

Do not attempt to remove spring from its housing. Clock- type springs can be dangerous to handle. Removal of spring from housing could result in personal injury.

The unique SAFETYCHANGE® spring motor consists of a spring and hub sealed within a housing. A replacement spring is supplied sealed in its housing and the old unit should be dis- carded completely.

1.

Turn off all electric power.

2.

Disconnect cable from machine junction box.

3.

Wind all cable onto reel to relieve all spring tension.

4.

Remove inspection cover from face of spring housing.

5.

Rotate spool clockwise and observe inner shaft. Shaft

 

should rotate clockwise and hub (with spring attached)

 

should remain stationary.

 

NOTE: Do not attempt to remove spring if resistance

 

is met or hub tends to rotate with shaft.

 

Continue to rotate spool and strike end of shaft

 

several sharp blows with a lead hammer or rubber mallet

 

until shaft rotates freely and hub remains stationary.

6.

Remove (4) nuts which secure spring motor(s) to frame.

 

SPRING

 

HOUSING

 

COVER

 

PLATE

 

SPRING

Figure 1

HUB

 

COUNTER-

 

CLOCKWISE

 

FOR STANDARD

 

ROTATION

Figure 2

SPANNER

WRENCH

7. Slide spring motor(s) off shaft and discard.

NOTE: On multi-spring reels, be sure to remove and save dowel pins which connect one spring hub with another. Also remove snap rings on shaft between spring housings.

8.Install replacement spring motor(s), pawls and pawl springs. NOTE: Pawl springs must be located between the pawls and the deepest section of the shaft grooves. Make sure

that pawls and pawl springs are inserted flush with ends of shaft and hub or they may rub against inspection cover.

SPRING

PAWL

CAUTION

Do not exceed number of turns indicated on serial plate. Over-tensioning can cause a broken spring, sheared shaft or other damage.

NOTE: If reel is equipped with ratcheted adjustment

wrench, follow instructions on separate sheet.

NOTE: On reels containing more than one spring, the hubs are connected at the factory. Therefore, by tightening the outer spring, the inside spring(s) will be tightened.

7.Remove collector cover and connect individual supply conductors to collector terminals. See ELECTRICAL CONNECTIONS diagram, on parts page.

SPOOL

 

 

HUB

SHAFT

 

 

(Spring not

 

 

 

shown)

 

SPRING

 

SHAFT

 

Install

 

SIDE VIEW

END VIEW

GROOVE

against flat

9.Tighten nuts (and extension bolts) securing spring housing(s) to reel frame.

10.Connect free end of cable to junction box on machine or adjust cord stop so that desired length of cord extends from reel.

11.Tension spring with spanner wrench. Refer to INSTALLATION section.

12.Replace inspection cover.

CONTINUED ON BACK PAGE

Page 2
Page 1
Image 1
Hubbell MMD28 manual Installation, Maintenance, Spring Replacement
Page 2

MMD28 specifications

The Hubbell MMD28 is a state-of-the-art lighting solution designed to cater to a wide range of indoor and outdoor applications. With an emphasis on durability, efficiency, and innovative technology, the MMD28 stands out in the competitive lighting marketplace. This versatile luminaire is ideal for use in industrial, commercial, and even residential settings, which makes it a popular choice among architects and engineers.

One of the standout features of the Hubbell MMD28 is its robust design. Constructed with high-quality materials, the fixture is built to withstand harsh environments, including extreme temperatures, moisture, and dust. This makes it suitable for use in warehouses, manufacturing facilities, and other challenging conditions. Its rugged housing ensures that the MMD28 can perform reliably over time, minimizing maintenance costs and downtime.

Another highlight of the MMD28 is its energy efficiency. The fixture is designed to deliver high lumen output while consuming minimal energy. It incorporates advanced LED technology that not only lowers energy costs but also contributes to a reduced carbon footprint. The LEDs used in the MMD28 have a long lifespan, which means fewer replacements and lower overall lifecycle costs.

The Hubbell MMD28 also features versatile mounting options, allowing for easy installation in various configurations. Whether it is mounted to a wall, ceiling, or suspended from a height, the fixture provides flexibility to meet diverse lighting needs. Additionally, the angle of illumination can be adjusted to ensure optimal lighting coverage for specific applications.

Furthermore, the MMD28 is equipped with cutting-edge control technologies. Optional features such as dimming capabilities and occupancy sensors enhance energy savings by adjusting light levels based on presence or time of day. These smart technologies not only improve energy efficiency but also create a more comfortable and productive environment for occupants.

Overall, the Hubbell MMD28 is a powerful lighting solution that combines durability, efficiency, and advanced technology. With its excellent performance characteristics, versatile applications, and smart control options, it meets the demands of modern lighting projects while striving to exceed user expectations. Whether for industrial use or sophisticated commercial spaces, the MMD28 delivers high-quality illumination suitable for any situation.
Top Page Image Contents