Manuals / Brands / Computer Equipment / Computer Monitor / Humminbird / Computer Equipment / Computer Monitor

Humminbird 1155C 2 Screws, 3 Cable Collector Cover, 1 Cable Collector Insert, Assembling the Cable Collector

1 129

Download 129 pages, 3.54 Mb

Assembling the Cable Collector1 Cable Collector Insert2 Screws3 Cable Collector Cover

12.Attach the cable collector insert to the cable collector cover using the (2) #6 Phillips screws provided.

13.Place the control head back onto the mounting bracket. Plug the assembled cable collector into the back of the control head, pushing gently but steadily until you feel the collector snap into place. Cable connectors and cable sockets are keyed to prevent reverse installation, so be careful not to force the connectors into the wrong sockets. Adjust the control head to the desired viewing angle and secure by tightening the gimbal knobs.

Plugging the Assembled Cable Connector into the Back of the Control Head

NOTE: You may wish to dress the cabling with nylon wire ties in order to hold the cables together and create a cleaner assembly.

The Humminbird® 1100 Series™ control head is now ready for operation.

Contents

Page Page Thank You Warranty © 2007 Humminbird®, Eufaula AL, USA. All rights reserved 1100 Series™ Introduction How GPS and Cartography Work MMC/SD Slot Accessory Bus Installation Overview Views Viewing Cartography Introduction to Navigation The Menu System Start-UpOptions Menu Screen Snapshot X-Press™Menu (Screen Snapshot View only) Navigation Menu Tab Chart Menu Tab Alarms Menu Tab Setup Menu Tab Views Menu Tab Accessories Menu Tab Troubleshooting Display Problems Finding the Cause of Noise 1100 Series™ Introduction Your 1100 Series™ Chartplotter comes in the following configuration: How GPS and Cartography Work •View current position •View current track (breadcrumb trail) MMC/SD Slot Inserting an MMC/SD into the Card Slot Software Updates Accessory Bus Accessories Menu Tab 1100 Series™ Accessories Accessory Bus Accessory Bus Basic installation tasks that you must perform include: •Installing the control head (choosing either gimbal or in-dashmounting) •Installing the GPS Receiver •Testing the complete installation Control Head Installation Gimbal Mounting the Control Head 1 Washer 2 Gimbal Knob 3 Gimbal Mounting Bracket 1 Mounting Screws 2 Washer or Cables Routed Directly Beneath Mounting Bracket 1 Gimbal Mounting Bracket 2 Hole Cover Thread the cables through the opening in the back of the cable collector cover Assembling the Cable Collector 1 Cable Collector Insert 2 Screws 3 Cable Collector Cover Plugging the Assembled Cable Connector into the Back of the Control Head In-DashMounting the Control Head Parts and tools specific to In-dashmounting are: •Threaded rods and hardware •In-dashmounting foam pads •In-dashmounting template Page Page or If you have… Then use: Receiver Receiver Base Stem Pipe 3.Use electrical tape to secure the NMEA cable to the receiver cable as shown 5.Attach the GPS receiver to its base using the included #6 - 7/8" screws Access Under Mounting Location NOTE: Installation details may vary with unit configuration 5. Align the GPS receiver screw holes over the pilot screw holes and attach with the #8 Finish Routing the Cable and Check GPS Receiver Operation Secure the cable along its path to the control head as needed with cable ties Testing the System Installation To test the installation: Getting Started - Using Your 1100 Series™ Screen VIEW Key ZOOM (+/-)Keys MENU Key Powering Up the Control Head 1100 Series™ Chartplotter Title Screen Latitude and Longitude Position of Cursor Waypoint 6Active Cursor Icon 7Boat Icon trackpoints Cartography Map Scale 18 NEXT: Next Waypoint in the Route Key Functions •POWER/LIGHT key •EXIT key •VIEW key •4-WAYCursor Control key MENU Key The MENU key is used to access the menu system 4-WAYCursor Control Key The 4-WAYCursor Control Key has multiple functions, depending on the situation: VIEW PRESET Keys EXIT Key The EXIT key has multiple functions, depending on the situation: •If an alarm is sounding, pressing EXIT will cancel the alarm •Pressing EXIT will cycle through the available views in reverse order INFO Key MARK Key GOTO Key The GOTO Key has multiple functions, depending on the situation: ZOOM (+/-)Keys Views The views available on your 1100 Series™ are: Bird’s Eye No Readouts GPS Bird's Eye No Readouts View Page Bird's Eye View Bird's Eye View (Standard) 2Time 3Latitude and Longitude Position of Boat VLT: Voltage Bird’s Eye View (Navigating) 1Next Waypoint 4XTE (Cross Track Error): Distance of Boat from Route Chart/Bird’s Eye Combo View Chart/Bird’s Eye Combo View (Standard) Map Scale Chart/Bird’s Eye Combo View (Navigating) 6NEXT: Next Waypoint in the Route Chart Window Bird’s Eye Window Chart/Chart Combo View NOTE: See Chart Views for more information about each side of this view Chart/Chart Combo View (Standard) 5VLT: Voltage Chart/Chart Combo View (Navigating) Chart No Readouts View Page Chart View Chart View (Standard) with optional-purchaseNavionics® Cartography Declutter Icons Chart View (with Cursor) with optional-purchaseNavionics® Cartography 1Cursor Info Box 2Latitude and Longitude Position of Cursor 3Distance: Distance to Cursor 4Bearing: Bearing to Cursor Chart View (Navigating) with optional-purchaseNavionics® Cartography NOTE: You may also choose Chart No Readouts View if you prefer Chart Instrument View Chart Instrument View (Standard) 2Latitude and Longitude Position of Boat GPS Receiver or GPS Receiver Chart Instrument View (Navigating) 2Compass 3Cartography 4Course Projection Line 5Next Waypoint Chart/Bird's Eye Instrument View Chart/Bird’s Eye Instrument View (Standard) Chart/Bird’s Eye Instrument View (Navigating) 4Time 5NEXT: Next Waypoint in the Route 6TTG: Time to Go to Waypoint 7DTG: Distance to Go to Waypoint Screen Snapshot View Working with screen snapshots is a four-stepprocess: 1.Enabling Screen Snapshot from the Accessories Menu 2.Making a Screen Snapshot using the MARK key 3.Viewing a Screen Snapshot using the Screen Snapshot View Screen Snapshot View Highlighted Screen Snapshot Thumbnail Screen Snapshot Thumbnail Unavailable icon Information Box Chart View showing the Waypoint Thumbnail Feature 3Distance to Cursor 4Bearing to Cursor 5Route 7Snapshot Waypoint Name Page Viewing Cartography Chart View with Cursor Present Page Introduction to Navigation Waypoints, Routes and Tracks Waypoints, Routes and Tracks 7TTG: Time to Go to Waypoint Save, Edit, or Delete a Waypoint •Name shows the waypoints alphabetically •Time shows the most recently-createdwaypoint first •Distance shows the closest waypoint first Navigate to a Waypoint or Position Add a Waypoint Target or Trolling Grid Chart View with Target Waypoint Target Chart View with Grid Waypoint Trolling Grid Waypoint in declutter mode Save, Edit or Delete a Route Save or Clear a Current Track Edit, Delete or Hide Saved Tracks Edit, Delete or Hide Saved Tracks Man Overboard (MOB) Navigation MOB Navigation 1Target Surrounding MOB Waypoint 2MOB Waypoint 3Boat Icon 4Position where Man Overboard was activated The Menu System 4-WAYCursor Control keys, as follows: specific menu tab select a specific menu item under that tab setting QUICK TIPS: NOTE: The 1100 Series™ defaults to Advanced User Mode on start-up Page Start-UpOptions Menu Start-UpOptions Menu •Normal •Simulator •System Status Simulator Simulator Exit the Simulator by powering your 1100 Series™ off System Status Use System Status to view system connections and to conduct a unit self-test Self Test Accessory Test Accessory Test lists the accessories connected to the system GPS Diagnostic View GPS Diagnostic View Sky Chart Satellite Being Used Navigation X-Press™Menu Active Side To select the Active Side: 1.Highlight Active Side on the Navigation X-Press™Menu Split Position To Adjust Split Screen Position Cursor to Waypoint (Chart or Combo view only) NOTE: This X-Press™menu item appears only if you have saved waypoints To move cursor to a saved waypoint: 1.Highlight Cursor to Waypoint on the Navigation X-Press™menu Clear Current Track To Clear Current Track: 1.Highlight Clear Current Track on the Navigation X-Press™Menu 2.Use the RIGHT 4-WAYCursor Control key to initiate clearing the current track Save Current Route Cancel Navigation To Cancel Navigation: 1.Highlight Cancel Navigation on the Navigation X-Press™Menu 2.Use the RIGHT 4-WAYCursor Control key to initiate canceling navigation Cancel MOB Navigation Remove Grid (Only if a Grid is active) To Remove a Grid: 1.Highlight Remove Grid on the Navigation X-Press™Menu 2.Use the RIGHT 4-WAYCursor Control key to remove the grid Select Readouts 5 Selectable Readouts (Non-NavigationOnly) Used by All Non-InstrumentViews 5 Selectable Readouts, Used by All Non-InstrumentViews; Non-NavigationMode COG manner. See the Glossary for more information Off Suppresses the readout so that no data shows in that position To Select Readouts: 1.Highlight Select Readouts on the Navigation X-Press™menu 2.Use the RIGHT 4-WAYCursor Control key to initiate this procedure Select Nav Readouts To Select Nav Readouts: 1.Highlight Select Nav Readouts on the Navigation X-Press™menu 5 Selectable Readouts Used by All Non-InstrumentViews; Navigation Mode Bearing North, 090° East, 180° is South, 270° is West) CMG/SMG time elapsed since starting navigation on the route Select Instrument Readouts 8 Selectable Readouts Page Screen Snapshot X-Press™Menu Delete Image To delete an image: On the Screen Snapshot View, use the UP and DOWN 2.Highlight Delete Image on the Screen Snapshot X-Press™menu Navigation Menu Tab NOTE: Menu choices will vary depending on system settings Navigation Menu Current Track Current Track allows you to view the Current Track submenu To view the Current Track Submenu: 1.Highlight Current Track on the Navigation main menu 2.Use the RIGHT 4-WAYCursor Control keys to view the Current Track submenu Waypoints Waypoints allows you to view the Waypoints submenu To view the Waypoints Submenu: 1.Highlight Waypoints on the Navigation main menu 2.Use the RIGHT 4-WAYCursor Control keys to view the Waypoints submenu Routes Routes allows you to view the Routes submenu To view the Routes Submenu: 1.Highlight Routes on the Navigation main menu 2.Use the RIGHT 4-WAYCursor Control keys to view the Routes submenu North Reference To change the North Reference setting: 1.Highlight North Reference on the Navigation main menu Trolling Grid Rotation To change the Trolling Grid Rotation setting: Track Min Distance To change the Track Minimum Distance setting: [International Units only] Track Color Range Navigation Menu Tab: Current Track Course Projection Line 3D View Outline Export All Nav Data Delete All Nav Data To Delete All Navigation Data: 2.Use the RIGHT 4-WAYCursor Control key to delete all navigation data Continuous Navigation Mode Continuous Navigation Mode allows you to continue to navigate and Chart Menu Tab Chart Menu Chart Detail Level To change the Chart Detail Level setting: 1.Highlight Chart Detail Level on the Chart main menu NOTE: Some chart details are only available with optional-purchaseMMC/SD cards Map Borders Spot Soundings NOTE: Spot Soundings are only available with optional-purchaseMMC/SD cards To change the Spot Soundings setting: 1.Highlight Spot Soundings on the Chart main menu Navaids on Bird's Eye View Chart Select To activate or de-activateChart Select: 1.Highlight Chart Select on the Navigation main menu NVB Chart Preference NVB Chart Preference allows you to choose what built-inchart to use Set Map Offset Set Map Offset allows you to change the map offset used by the 1100 Series™ To change the Map Offset setting: Clear Map Offset To Clear Map Offset: Alarms Menu Tab From any view, press the MENU key twice to access the Main Menu System. The Alarms tab will be the default selection Alarms Menu Alarm Volume Alarm Volume allows you to adjust the volume of the alarms To change the Alarm Volume setting: 1.Highlight Alarm Volume on the Alarms main menu Low Battery Alarm Off Course Alarm Off Course Alarm Arrival Alarm Circle To change the Off Course Alarm setting: 1.Highlight Off Course Alarm on the Alarms main menu Drift Alarm To change the Drift Alarm setting: 1.Highlight Drift Alarm on the Alarms main menu Setup Menu Tab From any view, press the MENU key twice to access the tabbed Main Menu System, then press the RIGHT cursor key until the Setup tab is selected Setup Menu Sound Volume To change the Sound Volume setting: 1.Highlight Sound Volume on the Setup main menu Units - Depth Units - Depth selects the units of measure for all depth-relatedreadouts Units - Speed Units - Speed selects the units of measure for speed-relatedreadouts To change the Units - Speed setting: 1.Highlight Units - Speed on the Setup menu User Mode Restore Defaults To Restore Defaults: 1.Highlight Restore Defaults on the Setup menu 2.Use the RIGHT 4-WAYCursor Control key to initiate restoring defaults Temp. Offset Daylight Saving Time To change the Daylight Saving Time setting: Position Format To change the Position Format setting: Time Format Date Format To change the Date Format: Digits Format To change the Digits Format setting: NMEA Output Setup Menu Tab: User Mode The following NMEA sentences are output: DPT - Depth MTW - Water Temperature IP Address Setup To use the IP Address Setup feature: 1.Highlight IP Address Setup on the Setup main menu 2.Use the RIGHT 4-WAYCursor Control key to display the IP Address Setup window Video Out The following views are available: Accessories Menu Tab Using Screen Snapshot To turn Screen Snapshot on or off: 1.Highlight Screen Snapshot on the Accessories main menu To make a screen snapshot (Screen Snapshot must be enabled): Make sure you have installed an To view screen snapshots: Make sure that the 2.Press the VIEW key until you see the Screen Snapshot View To view a screen snapshot using snapshot waypoints: 2.Press the VIEW key until you see the Chart View Chartplotter Doesn’t Power Up Problem Possible Cause Possible Source of Noise Isolation 1-YearLimited Warranty This warranty does not apply to a product that has been: •Improperly installed; •Damaged or has failed because of an accident or abnormal operation; •Repaired or modified by entities other than Humminbird® Humminbird® Service Policy http://www.humminbird.com Returning Your Unit for Service For IN-WARRANTYservice, complete the following steps: •Include a brief written description of the problem •Include a copy of your receipt (to show proof and date of purchase) For OUT-OF-WARRANTYservice, complete the following steps: 1100 Series™ Chartplotter Accessories 1100 Series™ include: Specifications Communication Humminbird® Fishing System Optional Accessories SystemLink, WeatherSense®, HumminbirdPC™ Power Requirement Glossary Track Cross Track Error Trackplotter Time to Go Course Over Ground True North SOG DTG Course Over Ground Chartplotter (Monday - Friday 8:00 a.m. to 4:30 p.m. Central Standard Time):