Manuals / Brands / Marine Equipment / Fish Finder / Humminbird / Marine Equipment / Fish Finder

Humminbird 150PT, 160pt, 190C PT, 190CPT 8.The display shows many black dots at high sensitivitysettings, 7.The display begins to fade out. Images are not as sharp as normal

1 44

Download 44 pages, 928.8 Kb

7.The display begins to fade out. Images are not as sharp as normal.

Check the inputvoltage. The PiranhaMAX™ will not operate on inputvoltages below 10 VDC.

8.The display shows many black dots at high sensitivitysettings.

You are seeing noise or interference caused by one of several sources.Noise can be caused by electronic devices. Turn off any nearby electronicsand see if the problem goes away. Noise can also be caused by the engine. If engine noise is causing the interference, the problem will intensifyat higher RPMs. Increase the engine speed with the boat stationary to isolate this cause. Propeller cavitation can also appear as noise on the display.If the transducer is mounted too close to the propeller,the turbulencegenerated can interfere with the sonar signal. Make sure that the transducer is mounted at least 15" (380 mm) from the propeller.

Contents

Page Thank You CAUTION: WARNING WEEE DIRECTIVE: © 2008 Humminbird®,EufaulaAL, USA. All rights reserved Table of Contents PiranhaMAX™ Portable Case Assembly Stowing the Portable Transducer Installing the Portable Case on the Boat Connecting the Transducer and Power Cables The Menu System Light (Setting Not Saved in Memory) Depth Range (Setting Not Saved in Memory) Chart Speed (Setting Saved in Memory) Contrast (Setting Saved in Memory) Page PiranhaMAX™ Portable Case Assembly •Assembling the PiranhaMAX™mount •Assembling the base and handle •Assembling the control head to the base and handle •Routing the cables in the base 1.Assembling the PiranhaMAX™ Mount Tilt and Swivel PiranhaMAX™ Mount 2.Assembling the Base and Handle Punching Holes Attaching the Mount to the Base Installing the Handle Onto the Base Assembling the Control Head to the Base and Handle Rear View 4.Routing the Cables in the Base Attaching the Battery Tie-DownStraps Pulling the Cables Through the Base Installing the Cables Onto the Base Tying Down the Cables 5.Assembling the Portable Case 6.Charging and Installing the Battery Installing the Battery 7.Assembling the Transducer Mounting Bracket Transducer Knuckle Positions Assemblingthe PortableBracket below). Hand tightenonly Assembling the Portable Bracket Ratchets Placed in Position 1.Connecting the Transducer and Power Cables to the Portable Case Plugging in the Transducer Connecting the Spade Clips) 2.Attaching the Portable Case to the Boat PortableCaseAssembly 1.Testing the Transducer Prior to Installation 2.Mounting the Portable Transducer on the Boat Portable Transducer Mount Portable Transducer Mount Transducer Running Angle Transducer Tie-DownStrap) Moving the Portable Fishfinder 2.Remove the case from the surface mount 4.Unplug the power cable when not in use Powering ON and OFF •Use Start-Upfor on the water use - Water Surface Line - Structure - Temperature - Upper Range 9- 83 kHz, Wide Beam Hollow Fish Symbol (Dual Beam Units only) PiranhaMAX™ Sonar Technology Single Beam Sonar Dual Beam Sonar The Menu System Light PiranhaMAX™Portables Sensitivity Depth Range Zoom Chart Speed Fish Alarm Large fish only Large/Medium fish only All fish Filter SetUp Menu Contrast • Battery Alarm Fish ID+TM Dual Beam Single Beam NOTE: Bottom Black View is not available on color models Battery Alarm (SetUp Menu) Language (SetUp Menu) (Setting Saved in Memory, International only) Units (SetUp Menu) Maintenance How to Remove Water from the Portable Case Troubleshooting 1.Nothing happens when I turn the unit on 2.There is no transducer detected 3.There is no bottom readingvisible on the display 5.The unit comes on before I press the POWER-MENUkey, and won’t turn off 6.I get gaps in the reading at certainspeeds 7.The display begins to fade out. Images are not as sharp as normal 8.The display shows many black dots at high sensitivitysettings International Purchases Humminbird®1-YearLimited Warranty This warranty does not apply to a product that has been: •Improperly installed; •Damaged or has failed because of an accident or abnormal operation; •Repaired or modified by entities other than Humminbird® PLEASE DO NOT RETURN THIS PRODUCT TO STORE FOR SERVICE Returning Your Unit for Service NOTE: Please do not return your Humminbird® to the store for service NOTE: For IN-WARRANTYservice, complete the following steps: •Include a brief written description of the problem Specifications 600 ft (185 m) – (PMAX150/160) 800 ft (250 m) – (PMAX190c) 800 Watts (PTP) – (PMAX150/160) 1600 Watts (PTP) – (PMAX190c) Page in any of the followingways: By Telephone By e-mail cservice@johnsonoutdoors.com For direct shipping, our address is: